Explanation Given: The specific weight of the material, γ = 90 lb / ft 3 . Show the assembly of the material as in Figure (1). From Figure 1, Compute the moment of inertia of the assembly about an axis passing through the center of mass O . I O = I G + m d 2 = I G + m ( a + b ) 2 (I) Here, the mass of the material is m , the diameter is d and the moment of inertia about G is I G . Compute the moment of inertia of the assembly about an axis passing through the center of mass G . I G = { 1 2 [ γ g π ( a + b ) 2 e ] ( a + b ) 2 − 1 2 [ γ g π b 2 e ] b 2 + 1 2 [ γ g π ( b ) 2 d ] b 2 − 1 2 [ γ g π ( e ) 2 ( d ) ] e 2 } (II) Here, the acceleration due to gravity is g . Compute the mass of the material. m = γ g π ( a + b ) 2 e − γ g π b 2 ( e − d ) − 4 [ γ g π ( a − d ) 2 d ] (III) Conclusion: Take the value of g as 32 .2 ft / s 2 . Substitute 32 .2 ft / s 2 for g , 0 .5 ft for a , 0 .25 ft for d , 2 ft for b , 1 ft for e , 1 ft for c , and 90 lb / ft 3 for γ in Equation (II). I G = { 1 2 [ 90 32.2 π ( 0.5 + 2 ) 2 ( 1 ) ] ( 0.5 + 2 ) 2 − 1 2 [ 90 32.2 π ( 2 ) 2 ( 1 ) ] ( 2 ) 2 + 1 2 [ 90 32.2 π ( 2 ) 2 ( 0.25 ) ] ( 2 ) 2 − 1 2 [ 90 32.2 π ( 1 ) 2 ( 0.25 ) ] ( 1 ) 2 } = { ( 0

Engineering Mechanics: Statics and Study Pack (13th Edition)

13th Edition

ISBN: 9780133027990

Author: Russell C. Hibbeler

Publisher: Prentice Hall

See similar textbooks

Question

Chapter 10.8, Problem 109P

To determine

The moment of inertia of the wheel about an axis passing through the point O.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 10.8, Problem 108P

Chapter 10.8, Problem 110RP

Students have asked these similar questions

Homework#5

If the 50 mm diameter shaft is made from brittle material having an ultimate strength of σult=595 MPa for both tension and compression, determine the factor of safety of the shaft against rupture. The applied force, F, is 140 kN. The applied torque T, is 5.0 kN⚫m. Enter your answer to a precision of two decimal places. T F

Oxygen (molar mass 32 kg/kmol) expands reversibly in a cylinder behind a piston at a constant pressure of 3 bar. The volume initially is 0.01 m3 and finally is 0.03 m3; the initial temperature is 17°C. Calculate the work input and the heat supplied during the expansion. Assume oxygen to be an ideal gas and take cp = 0.917 kJ/kg K. For 1 bonus mark explain why (using your understanding of thermodynamics) that oxygen is used in this context rather than water vapour.

Chapter 10 Solutions

Engineering Mechanics: Statics and Study Pack (13th Edition)

Ch. 10.3 - Determine the moment of inertia of the shaded area...Ch. 10.3 - Determine the moment of inertia of the shaded area...Ch. 10.3 - Determine the moment of inertia of the shaded area...Ch. 10.3 - Determine the moment of inertia of the shaded area...Ch. 10.3 - Prob. 1P Ch. 10.3 - Prob. 2P Ch. 10.3 - Prob. 3P Ch. 10.3 - Prob. 4P Ch. 10.3 - Prob. 5P Ch. 10.3 - Prob. 6P

Knowledge Booster

The moment of inertia of the wheel about an axis passing through the point O .

The moment of inertia of the wheel about an axis passing through the point O.

Want to see the full answer?

Chapter 10 Solutions