VEC MECH 180-DAT EBOOK ACCESS(STAT+DYNA)
12th Edition
ISBN: 9781260916942
Author: BEER
Publisher: MCG
expand_more
expand_more
format_list_bulleted
Videos
Question
Chapter 10.1, Problem 10.49P
To determine
Derive the expression for the
Show that the mechanical efficiency cannot exceed 1/2 if the block is to remain in place when the force P is removed.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A block with weight W is pulled up a plane forming an angle a with the horizontal by a force P directed along the plane. μ If is the coefficient of friction between the block and the plane, derive an expression for the mechanical efficiency of the system. Show that the mechanical efficiency cannot exceed 1/2 if the block is to remain in place when the force P is removed.
.A belt 200 mm wide and 7 mm thick drives a pulley at belt speed of 25 m/s. The density of the belt is 980 kg/m3 and the coefficient of friction between the belt and pulley is 0.23. Given that the angle of contact of pulley is 2π/3 and the allowable stress of the belt is 1.8 MPa, determine the tension on the slack side of the belt (T2) in N
A 20 kg block is held in place on an incline plane as shown by a rope that passesover a frictionless pulley at B and then over a fixed cylinder at C where thecoefficient between the rope and the fixed cylinder is 0.2. Given an angle ofincline, A = 25°, if a force of P = 200 V is applied to the end of the rope,(a) Will the block move if the coefficient of static friction between the block and theinclined surface is M, = 0.56?(b)If impending motion exists, will the block tip or slip?
Chapter 10 Solutions
VEC MECH 180-DAT EBOOK ACCESS(STAT+DYNA)
Ch. 10.1 - Determine the vertical force P that must be...Ch. 10.1 - Determine the horizontal force P that must be...Ch. 10.1 - Prob. 10.3PCh. 10.1 - Prob. 10.4PCh. 10.1 - Prob. 10.5PCh. 10.1 - A spring of constant 15 kN/m connects points C and...Ch. 10.1 - The two-bar linkage shown is supported by a pin...Ch. 10.1 - Determine the weight W that balances the 10-lb...Ch. 10.1 - Prob. 10.9PCh. 10.1 - Prob. 10.10P
Ch. 10.1 - Solve Prob. 10.10, assuming that the force P...Ch. 10.1 - Prob. 10.12PCh. 10.1 - Prob. 10.13PCh. 10.1 - Prob. 10.14PCh. 10.1 - Prob. 10.15PCh. 10.1 - 10.15 and 10.16 Derive an expression for the...Ch. 10.1 - Prob. 10.17PCh. 10.1 - Prob. 10.18PCh. 10.1 - Prob. 10.19PCh. 10.1 - Prob. 10.20PCh. 10.1 - Prob. 10.21PCh. 10.1 - A couple M with a magnitude of 100 Nm isapplied as...Ch. 10.1 - Rod AB is attached to a block at A that can...Ch. 10.1 - Solve Prob. 10.23, assuming that the 800-N force...Ch. 10.1 - In Prob. 10.9, knowing that a = 42 in., b = 28...Ch. 10.1 - Determine the value of corresponding to...Ch. 10.1 - Prob. 10.27PCh. 10.1 - Determine the value of corresponding to...Ch. 10.1 - Prob. 10.29PCh. 10.1 - Two rods AC and CE are connected by a pin at Cand...Ch. 10.1 - Solve Prob. 10.30 assuming that force P is movedto...Ch. 10.1 - Prob. 10.32PCh. 10.1 - Prob. 10.33PCh. 10.1 - Prob. 10.34PCh. 10.1 - Prob. 10.35PCh. 10.1 - Prob. 10.36PCh. 10.1 - Prob. 10.37PCh. 10.1 - Prob. 10.38PCh. 10.1 - Prob. 10.39PCh. 10.1 - Prob. 10.40PCh. 10.1 - Prob. 10.41PCh. 10.1 - The position of boom ABC is controlled by...Ch. 10.1 - Prob. 10.43PCh. 10.1 - Prob. 10.44PCh. 10.1 - Prob. 10.45PCh. 10.1 - Prob. 10.46PCh. 10.1 - Denoting the coefficient of static friction...Ch. 10.1 - Prob. 10.48PCh. 10.1 - Prob. 10.49PCh. 10.1 - Prob. 10.50PCh. 10.1 - Prob. 10.51PCh. 10.1 - Prob. 10.52PCh. 10.1 - Prob. 10.53PCh. 10.1 - Prob. 10.54PCh. 10.1 - Prob. 10.55PCh. 10.1 - Prob. 10.56PCh. 10.1 - Prob. 10.57PCh. 10.1 - Determine the horizontal movement of joint C if...Ch. 10.2 - Using the method of Sec. 10.2C, solve Prob. 10.29....Ch. 10.2 - Prob. 10.60PCh. 10.2 - Prob. 10.61PCh. 10.2 - Prob. 10.62PCh. 10.2 - Prob. 10.63PCh. 10.2 - Prob. 10.64PCh. 10.2 - Prob. 10.65PCh. 10.2 - Using the method of Sec. 10.2C, solve Prob. 10.38....Ch. 10.2 - Prob. 10.67PCh. 10.2 - Prob. 10.68PCh. 10.2 - Prob. 10.69PCh. 10.2 - Prob. 10.70PCh. 10.2 - Prob. 10.71PCh. 10.2 - Prob. 10.72PCh. 10.2 - Prob. 10.73PCh. 10.2 - Prob. 10.74PCh. 10.2 - A load W of magnitude 144 lb is applied to...Ch. 10.2 - Solve Prob. 10.75, assuming that the spring...Ch. 10.2 - Bar ABC is attached to collars A and B that...Ch. 10.2 - Solve Prob. 10.77, assuming that the spring...Ch. 10.2 - Prob. 10.79PCh. 10.2 - Prob. 10.80PCh. 10.2 - Prob. 10.81PCh. 10.2 - A spring AB of constant k is attached to two...Ch. 10.2 - Prob. 10.83PCh. 10.2 - Prob. 10.84PCh. 10.2 - Prob. 10.85PCh. 10.2 - Prob. 10.86PCh. 10.2 - Prob. 10.87PCh. 10.2 - Prob. 10.88PCh. 10.2 - Prob. 10.89PCh. 10.2 - Prob. 10.90PCh. 10.2 - Prob. 10.91PCh. 10.2 - Prob. 10.92PCh. 10.2 - Prob. 10.93PCh. 10.2 - Prob. 10.94PCh. 10.2 - Prob. 10.95PCh. 10.2 - Prob. 10.96PCh. 10.2 - Bars AB and BC, each with a length l and of...Ch. 10.2 - Solve Prob. 10.97 knowing that l = 30 in. and k =...Ch. 10.2 - Bars AB and CD, each of length l and of negligible...Ch. 10.2 - Solve Prob. 10.99, assuming that the vertical...Ch. 10 - Determine the vertical force P that must be...Ch. 10 - Determine the couple M that must be applied...Ch. 10 - Prob. 10.103RPCh. 10 - Prob. 10.104RPCh. 10 - Prob. 10.105RPCh. 10 - Prob. 10.106RPCh. 10 - Prob. 10.107RPCh. 10 - Prob. 10.108RPCh. 10 - Prob. 10.109RPCh. 10 - Prob. 10.110RPCh. 10 - Prob. 10.111RPCh. 10 - Prob. 10.112RP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016, determine the force F required to advance the bar at a constant speed.arrow_forwardA 20 kg block is held in place on an incline plane as shown by a rope that passes over a frictionless pulley at B and then over a fixed cylinder at C where the coefficient between the rope and the fixed cylinder is 0.2. Given an angle of incline, 0 = 25°, if a force of P = 200 N is applied to the end of the rope, (a) Will the block move if the coefficient of static friction between the block and the inclined surface is μ = 0.56? (b)lf impending motion exists, will the block tip or slip? Enter the magnitude of force in the rope that will cause tipping of the block as the answer in the Respondus answer-box. 0.4 m 0.8 m Ө MA 0.5 m C B Parrow_forwardA 20 kg block is held in place on an incline plane as shown by a rope that passes over a frictionless pulley at B and then over a fixed cylinder at C where the coefficient between the rope and the fixed cylinder is 0.2. Given an angle of incline, 0 = 25°, if a force of P = 200 N is applied to the end of the rope, (a) Will the block move if the coefficient of static friction between the block and the inclined surface is μ = 0.56? (b)lf impending motion exists, will the block tip or slip? Enter the magnitude of force in the rope that will cause tipping of the block as the answer in the Respondus answer-box. 0.4 m 0.8 m MA 0.5 m C B Parrow_forward
- A 400-N cabinet is being pushed by a man on a concrete floor with a coefficient ofstatic friction of 0.37 and a coefficient of kinetic friction of 0.12. He exerts a force, F, of100 N at an angle of θ = 20° on the cabinet.Determine:i. The normal force, N (draw the FBD)ii. The characteristic of friction or the state of motion (static or kinetic)iii. The value of the actual friction force, Ff (show the equations of equilibrium)iv. The value of F if the motion is impending (show the equations of equilibrium)arrow_forwardTwo blocks A and B weighing 3 kN and 15 kN, respectively, are held in position against an inclined plane by applying a horizontal force P as shown in Fig. Find the least value of P which will induce motion of the block A upwards. Angle of friction for all contact surfaces is 12°.7.arrow_forwardA 60-kg cabinet is mounted on casters that can be locked to prevent their rotation. The coefficient of static friction between the floor and each caster is 0.35. 3. If h = 600 mm, determine the magnitude of the force P (in N) required to move the cabinet to the right if the casters at A are locked and the casters at B are free to rotate. (ANSWER: 72.5)arrow_forward
- A 60-kg cabinet is mounted on casters that can be locked to prevent their rotation. The coefficient of static friction between the floor and each caster is 0.35. 1. If h = 600 mm, determine the magnitude of the force P (in N) required to move the cabinet to theright, if all the casters are locked. (ANSWER: 206) 2. If h = 600 mm, determine the magnitude of the force P (in N) required to move the cabinet to the right if the casters at B are locked and the casters at A are free to rotate. (ANSWER: 178)arrow_forward• Draw a free body diagram of the box on the incline. . Determine the weight (W) of the box on the incline surface. Determine the normal force (N) acting on the inclined box. Determine the friction force (F) acting on the inclined box. ● 7. A box of unknown weight is being pulled on a = 39 degree inclined surface by a frictionless pully system attached to a 540 pound box hanging off the pully. The coefficient of static friction between the box and the inclined surface is μ = 0.33 and both boxes are not moving. Answer the questions below: ● W= N = Ff= 0 W lbs lbs lbs 540 lbsarrow_forwardThe power transmitted between two shafts 3.5 metres apart by a cross belt drive round the two pulleys 600 mm and 300 mm in diameters, is 6 kW. The speed of the larger pulley (driver) is 220 r.p.m. The permissible load on the belt is 25 N/mm width of the belt which is 5 mm thick. The coefficient of friction between the smaller pulley surface and the belt is 0.35. Determine : 1. necessary length of the belt ; 2. width of the belt, and 3. necessary initial tension in the belt. [Ans. 8.472 m; 53 mm ; 888 N] Subject:Theory of Machinesarrow_forward
- EXERCISE 2.34 The cable, whose length is 300 mm, is fastened to the 500-g block. Clockwise rotation of the arm at a constant angular speed of 5 rad/s causes the block to slide outward. The motion occurs in the vertical plane, and the coefficient of sliding friction is 0.4. Determine the tensile force in the cable and the force exerted by the block on the walls of the groove when = 53.1301⁰. 300 mm -300 mm- (Hint: use polar coordinates to solve the problem. R is from the rotation center of the arm to the block and is as shown in the Figure. Let L be the total length of the cable and S be the length from the clamped end of the cable to the end of the arm.)arrow_forwardA 50 kN block is resting on a horizontal plane with a coefficient of statics friction of 0.3. Determine the minimum force P to start the motion of the block to the right, if it is applied on the block: a. Horizontally to the right. Ans: 15kN b. Downward to the right, 30° with the horizontal Ans: 20.95KNarrow_forwardAs shown, a man is leaning against the side of a cabinet with an unusual design. The cabinet's main body weighs 25 kg, while the upper rectangular portion weighs 3 kg. Assume the coefficients of friction between the cabinet and the floor are μs = 0.33 and μk = 0.28. Knowing that the force P exerted by the man's shoulder on the horizontal cabinet: 2. Determine which of the following is the CORRECT equilibrium equation obtained from the system's force diagram. A. ΣF = 0: N - 245.25 = 0B. ΣF = 0: P - μ N = 0C. ΣM = 0: 245.25(0.55) + 29.43(0.2) - N(x) - P(1.5) = 0arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
International Edition---engineering Mechanics: St...Mechanical EngineeringISBN:9781305501607Author:Andrew Pytel And Jaan KiusalaasPublisher:CENGAGE L
International Edition---engineering Mechanics: St...
Mechanical Engineering
ISBN:9781305501607
Author:Andrew Pytel And Jaan Kiusalaas
Publisher:CENGAGE L
How to balance a see saw using moments example problem; Author: Engineer4Free;https://www.youtube.com/watch?v=d7tX37j-iHU;License: Standard Youtube License