AUTOMOTIVE TECHNOLOGY -W/MINDTAP ACCESS
7th Edition
ISBN: 9780357096789
Author: ERJAVEC
Publisher: CENGAGE L
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 10, Problem 5MC
Which cleaning method uses high-frequency sound waves to create microscopic bubbles that loosen dirt from parts?
- Ultrasonic
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
.
one or more can be correct please select from below options
Lower operating temperatures are more desirable as they reduce the viscosity making it easier to fill the cavity
This process can be used for both thermosets and thermoplastics as they can both be thermally shaped
This process can only be used for thermosets as they can thermally cure from the monomer state
This process is suitable for rubber, PVC and polymethyl methacrylate
How is it possible to decrease contact resistance?
O By using different fluids for better matching
O Using softer metal foils
Increasing surface roughness
O None of the above
O Using higher pressure when combining
Which one of these may increase the amount of contact resistance?
Lower temperature during matching of materials
decreasing pressure for pressing the materials together
Higher surface roughness
All of the above
Using air as a fluid for the gap instead of liquids
Chapter 10 Solutions
AUTOMOTIVE TECHNOLOGY -W/MINDTAP ACCESS
Ch. 10 - WHat should be worn when working with any type of...Ch. 10 - Why should a memory saver be installed before dis...Ch. 10 - Prob. 1TFCh. 10 - True or False? The first step in removing an...Ch. 10 - Prob. 3TFCh. 10 - What is the best way to lift a vehicle when...Ch. 10 - Prob. 2MCCh. 10 - The buildup of minerals and deposits inside the...Ch. 10 - Hydrocarbon solvents are. flammable toxic both a...Ch. 10 - Which cleaning method uses high-frequency sound...
Ch. 10 - Parts must be when they go into an abrasive blast...Ch. 10 - Prob. 7MCCh. 10 - Which of the following is not considered part of...Ch. 10 - Which of the following statements is not true...Ch. 10 - Which of the following is not a common way to...Ch. 10 - While working on an engine with an excessive...Ch. 10 - While discussing the common causes for cracks...Ch. 10 - Technician A uses a crane to remove an engine from...Ch. 10 - Prob. 4ASRQCh. 10 - While discussing abrasive cleaners: Technician A...Ch. 10 - Technician A labels or marks all electrical wires...Ch. 10 - While discussing cleaning engine parts: Technician...Ch. 10 - While loosening the axle shaft hub nuts on a FWD...Ch. 10 - While preparing to remove an engine: Technician A...Ch. 10 - After removing the vehicles hood in preparation...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Which of the following statements is not true about thermal cleaning? The main advantage of thermal cleaning is a total reduction of all oils and grease on and in blocks, heads, and other parts. After a part has been thermally cleaned, it should be submerged in water to cool it quickly. Thermal cleaning leaves behind a dry, powdery ash on the parts. After a part has been thermally cleaned, it should be washed or blasted with shotarrow_forwardWhat cautions must be taken when chemically cleaning oil or paint from a piece of metal?arrow_forwardWhat properties should a good leak-detecting solution have?arrow_forward
- Generally speaking what is the first step in air treatmentarrow_forwardWhich type of material thermosetting or thermal plastic can be easily injected by pressure into a mold? a thermostat b thermoplastic c all of the above d none of the abovearrow_forwardWhich of the following statements about latex and nitrile gloves is not true? The gloves offer protection against cuts. The gloves offer protection against disease and grease buildup under and around your fingernails. Latex gloves are more comfortable but weaken when they are exposed to gas, oil, and solvents. Nitrile gloves are not as comfortable but they are not affected by gas, oil, and solvents.arrow_forward
- What is use to clean solutions that eventually become spent and must be disposed of properlyarrow_forwardWhich thermal spray process can be used to apply ceramics?arrow_forwardWhich of the following statements is not true regarding the use of grease with ground glass joints. Group of answer choices The grease helps to make a better seal between ground glass joints The grease should be applied to the male fitting of a ground glass joint before connecting and rotating the joints together Excess grease can be removed first with a paper towel and then with a wipe moistened with a non-polar solvent like hexane Too much grease on the joints is never a problem The joint will become transparent all the way around when the proper amount of grease is appliedarrow_forward
- Which of the following is true for redox markers? I- color change occurs when the reagent changes from oxidizing form to reducing form II- the color of the oxidizing form of the reagent occurs when the ratio of the reducing form to the oxidizing form is 1/10 III- range of token functions is E0 ± 0.0592/n IV- the color of the reducing form of the reagent occurs when the ratio of the reducing form to the oxidizing form is 1/10arrow_forwardWhat are the drawbacks of wet scrubbers?arrow_forwardIt says surface Temperature is not 125.49oC (look at picture I attached). What would be the correct value? Thank you.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Electrical Transformers and Rotating MachinesMechanical EngineeringISBN:9781305494817Author:Stephen L. HermanPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Electrical Transformers and Rotating Machines
Mechanical Engineering
ISBN:9781305494817
Author:Stephen L. Herman
Publisher:Cengage Learning
Principles of Lubrication | Automobile Engineering; Author: Magic Marks;https://www.youtube.com/watch?v=MGbbSxZTdCQ;License: Standard Youtube License