Degarmo's Materials And Processes In Manufacturing
Degarmo's Materials And Processes In Manufacturing
13th Edition
ISBN: 9781119492825
Author: Black, J. Temple, Kohser, Ronald A., Author.
Publisher: Wiley,
bartleby

Concept explainers

Joining Processes
It is the process of permanent or temporary joining of two metal pieces with the help of heat or pressure. Two metal parts are assembled by applying an energy source for the formation of a single unit. The obtained joined metals cannot be fragmented easi…
bartleby

Videos

Textbook Question
Book Icon
Chapter 10, Problem 13RQ

Why might you use a shrink fit to join the wheels of trains to the axle rather than welding them?

Expert Solution & Answer
Check Mark

Want to see the full answer?

Check out a sample textbook solution
Blurred answer
Previous
Chapter 10, Problem 12RQ
Next
Chapter 10, Problem 14RQ
Students have asked these similar questions
Where is a bent material most likely to fail?
What are the compatibility requirements for the body?
Why it is important to loosen one screw before tightening the opposing one by an equal amount?

Chapter 10 Solutions

Degarmo's Materials And Processes In Manufacturing

Ch. 10 - What are some of the advantages to the consumer of...Ch. 10 - DFMÂ stands for design for manufacturing. Why is...Ch. 10 - Explain the difference between attributes and...Ch. 10 - Prob. 4RQCh. 10 - What are the four basic measures upon which all...Ch. 10 - What are gage blocks?Ch. 10 - Why do gage blocks come in sets?Ch. 10 - Prob. 8RQCh. 10 - What is the difference between accuracy and...Ch. 10 - What is the difference between tolerance and...
Ch. 10 - Prob. 11RQCh. 10 - Prob. 12RQCh. 10 - Why might you use a shrink fit to join the wheels...Ch. 10 - Explain the difference between repeatability and...Ch. 10 - When measuring time, is it more important to be...Ch. 10 - Prob. 16RQCh. 10 - What factors should be considered in selecting...Ch. 10 - Prob. 18RQCh. 10 - What is parallax? (Why do linesmen in tennis sit...Ch. 10 - Explain the rule of 10 in terms of tolerances.Ch. 10 - How does the vernier caliper work to make...Ch. 10 - What are the two most likely sources of error in...Ch. 10 - What is the major disadvantage of a micrometer...Ch. 10 - What is the main advantage of a micrometer over...Ch. 10 - What is the major difficulty in obtaining an...Ch. 10 - Why is the toolmakers microscope particularly...Ch. 10 - What are the ways that linear measurements can be...Ch. 10 - What type of instrument would you select for...Ch. 10 - What are the chief disadvantages of using a vision...Ch. 10 - What is a CMM (coordinate measuring machine)?Ch. 10 - Prob. 31RQCh. 10 - How can the no�go member of a plug gage be...Ch. 10 - What is the primary precaution that should be...Ch. 10 - What tolerances are added to gages when they are...Ch. 10 - Explain how a go/no�go ring gage works to check...Ch. 10 - Why are air gages particularly well suited for...Ch. 10 - Explain the principle of measurement by...Ch. 10 - How does a toolmakers flat differ from an optical...Ch. 10 - Prob. 1PCh. 10 - Read the 25�division vernier graduated in metric...Ch. 10 - In Figure 10.C , the sleeve�thimble region of...Ch. 10 - Suppose that in Figure 10.31 the height of the...Ch. 10 - What is the estimated error in this measurement,...Ch. 10 - Figure 10.D shows the sleeve�thimble region of...Ch. 10 - In Figure 10.E , two examples of a metric...Ch. 10 - Prob. 8PCh. 10 - Figure 10.F shows a section of a vernier...Ch. 10 - Here is a table that provides a description of...

Additional Engineering Textbook Solutions

Find more solutions based on key concepts
A rocket sled is to be slowed from an initial speed of 300 m/s by lowering a scoop into a water trough. The sco...

Fox and McDonald's Introduction to Fluid Mechanics

The temperature of water at outlet.

Introduction to Heat Transfer

Determine and plot the moment M required to rotate arm OA over the range 0180. Find the maximum value of M and ...

Engineering Mechanics: Statics

A common procedure for cooling a high-performance computer chip involves joining the chip to a heat sink within...

Fundamentals of Heat and Mass Transfer

The impulses created by a falling weight onto a sample of URETHANE foam and CONFOR foam.

Engineering Mechanics: Statics & Dynamics (14th Edition)

What parts are included in the vehicle chassis?

Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)

Knowledge Booster
Background pattern image
Mechanical Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
Text book image
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Text book image
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning
Text book image
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
SEE MORE TEXTBOOKS
Metal Joining Process-Welding, Brazing and Soldering; Author: Toc H Kochi;https://www.youtube.com/watch?v=PPT5_fDSzGY;License: Standard YouTube License, CC-BY