Principles of Foundation Engineering (MindTap Course List)
9th Edition
ISBN: 9781337705028
Author: Braja M. Das, Nagaratnam Sivakugan
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Question
Chapter 10, Problem 10.4P
To determine
Find the allowable net pressure using Equation 9.51 and 10.14.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A 10 m x 6 m mat foundation is placed at 2.0 m depth in sand where the average value of N60 is 23. Determine the allowable net pressure that would limit the settlement to 75 mm, using the following equations.
Question attached
10.6
Chapter 10 Solutions
Principles of Foundation Engineering (MindTap Course List)
Ch. 10 - Refer to the rectangular combined footing in...Ch. 10 - Prob. 10.2PCh. 10 - Prob. 10.3PCh. 10 - Prob. 10.4PCh. 10 - Prob. 10.5PCh. 10 - Prob. 10.6PCh. 10 - Prob. 10.7PCh. 10 - Prob. 10.8PCh. 10 - A plate loading test was carried out on a medium...Ch. 10 - A 300 mm 450 mm plate was used in carrying out a...
Knowledge Booster
Similar questions
- X=30arrow_forwardPlease solve with a good explantion and step by step solutionarrow_forwardA footing of size 2m x 2m transferring a pressure of 200 kN/m2, is placed at depth of 1.5 m below the ground as shown in the figure (not drawn to the scale). The clay stratum is normally consolidated. The clay has specific gravity of 2.65 and compression index of 0.3. 200 kN/m? 1.5 m GWT Ya = 15 kN/m 18 kN/m elemiu 1 m Silty Sand Ysat = 10.5 m 1.5 m Clay Yat = 17 kN/m Dense Sand Consideration 2:1 (vertical to horizontal) method of load distribution and yw primary consolidation settlement (in mm, round off to two decimal places) of the clay stratum is 10kN/m, thearrow_forward
- A footing of size 2m×2m transferring a pressure of 200 kN/m², is placed at a depth of 1.5 m below the ground as shown in the figure (not drawn to the scale). The clay stratum is normally consolidated. The clay has specific gravity of 2.65 and compression index of 0.3. 1.5m 1m 1.5 m 200 kN/m² Silty sand Clay Ya =15kN/m³ Y sat = 18kN/m³ Y sat = 17 kN/m³ GWT $0.5 m Dense sand Considering 2:1 (vertical to horizontal) method of load distribution and Y₁ = 10kN/m³, the primary consolida- tion settlement (in mm, round off to two decimal places) of the clay stratum isarrow_forward(b) Figure Q2 (b) shows the ring foundation to support a silo. Given R1 = 3 m while R2 =6 m. The total vertical load is 7500 kN. (i) Calculate and plot the vertical stress increase with depth up to 7 m (use 1 minterval) under the centre of the ring (point O).(ii) Determine the maximum vertical stress increase and its location.arrow_forwardThe attached figure shows the plan of rectangular foundation which transmits a uniform contact pressure of 120 kN/m2. The width of the foundation is 15 m. A) Determine the increase in vertical pressure at a depth of 10 m below point A B) The vertical stress at a depth of 10m below point Barrow_forward
- Q3. Two meters of compacted fill (y= 20 kN/m³) is placed over a large area (Figure 4). A rectangular foundation of size 4 m x 5 m is constructed at the site with its base located at the existing ground surface. GWT is found at a depth of 3 m below the existing ground surface. a). Calculate and plot the in-situ vertical effective stress profile to a depth of 16 m below the existing ground surface prior to fill and footing placement. Use points with z = +2, +1, 0, -1, -2, -3, -5, -10, -13, -16 m (with z measured from the existing ground surface). b). Calculate and plot the additional effective stress due to the fill to a depth of 16 m. Use the same points as in part a). c). If the load applied on the foundation is 4 MN, calculate and plot the effective stress increase due to the footing to a depth of 16 m. Use the 2:1 approximate method and the same points as in part a). Summarize your calculations in an Excel spreadsheet and present sample calculations for z = 0, -3, -10 and -16 m (with…arrow_forwardThe plan of a rectangular foundation shown in figure transmits a uniform contact pressure of 120 kN/m². Determine the vertical stress induced by this loading at point B under a depth of 5 m. (40 marks) 25.0- 15.0 6.0- 4.0 B•arrow_forwardA rectangular footing (4.89 x 4.38 m.) is placed 1.21 m. below the ground surface. The soil arrangement is composed of sand (ground) for the first 6.52 meters and followed by clay for the next 6.98 meters. The force acting on the footing is 10,293 kN. Determine the resulting stress increase at the midheight of the consolidating layer in kPa. Assume a 2V:1H pressure diagram. Unit weight of sand = 16.1 kN/m3. Unit weight of clay = 18.7 kN/m3. Use stored value. Answer in five decimal places.arrow_forward
- 2 m 3 m 3 m 1 m 5. Refer to Prob. 3. Determine the vertical stress at a depth of 2.5 m below point E in Fig. Prob. 3. All the other data given in Prob. 3 remain the same. 6. A rectangular footing 6x3 m carries a uniform pressure of 300 KN/m2 on the surface of of a soil mass. Determine the vertical stress at a depth of 4.5 m below the surface on the center line 1.0 m inside the long edge of the foundation. 7. A tower is founded on a circular ring type foundation. The width of the ring is 4 m and its internal radius is 8m. Assuming the distributed load per unit area as 300 KN/m2, determine the vertical pressure at a depth of 6 m below the center of the foundation. The footing is founded at a depth of 2.5m below the ground surface. 8. The L-shaped area shown in figures carries a 96KN/m2 uniform load. Find the vertical increment due to the structure load at a depth of 8m below comers A and E. Sm 4m 6.5m 4m E- 9. The plan of a rectangular loaded area is shown in the figure. The uniformly…arrow_forwardShow complete solution and neat handwriting.arrow_forwardA 1.8 m square, 2 m deep and 1 m high footing supports a column load of 570 kN. It is supported on a clayey sand. There is no water present at the site. Use unit weight for the concrete 24 kN/m³. A dilatometer test run at the site has returned the following constrained modulus profile: Depth (m) M (MPa) 2 7.7 3 8.8 4 5 10.2 14.8 6 15.4 Plot the modulus distribution with depth considering both the strain distribution with depth and the soil moduli, and divide soil into 5 layers, then determine the average modulus for each soil layer.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Principles of Foundation Engineering (MindTap Cou...Civil EngineeringISBN:9781337705028Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage Learning
Principles of Foundation Engineering (MindTap Cou...
Civil Engineering
ISBN:9781337705028
Author:Braja M. Das, Nagaratnam Sivakugan
Publisher:Cengage Learning