Concept explainers
In a work situation where an electrician’s hands get wet while operating a 120-volt, corded drill, which of the following would be true? (Objective 1-1)
a. Body resistance increases, and any shock would be mild.
b. Body resistance remains the same, and there is no danger as Long as rubber boots are worn.
c. Body resistance is substantially decreased, and severe shock could occur.
d. There is no danger as Long as a three-prong plug is used.
The true statement for the situation where an electrician’s hands get wet while operating a
Answer to Problem 1RQ
Option (c) Body resistance is substantially decreased, and severe shock could occur.
Explanation of Solution
Introduction:
According to the Ohm’s law, the relation between the current, voltage, and resistance is given by,
Here, the current is in amperes, voltage is in volts, and resistance is measured in Ohm’s.
The flow of current through any material depends upon the resistance provided by the material. The higher is the circuit resistance, the lower the current flow that a voltage can push through the circuit and vice-versa.
Dry skin offers much more resistance in comparison to the wet body. This means that higher the resistance value, the more opposition to the current flow through the body.
The following table shows the value of resistance with respect to the different conditions:
Skin Condition | Resistance |
Dry skin | |
Sweaty hands | |
In water |
As shown in the above table, the value of resistance for wet hands is very less so if in a work situation where an electrician’s hands get wet while operating a
As shown in the above table, the value of resistance for wet hands is very less, so the shock will not be mild. Thus, option (a) is incorrect.
Therefore, the body resistance will not remain the same if the hand gets wet. Thus, option (b) is incorrect.
The electrician will always be in danger if his hands are wet. Thus, option (d) is incorrect.
Conclusion:
Therefore, the Option (c) Body resistance is substantially decreased, and severe shock could occur is best suitable answer for the given statement.
Want to see more full solutions like this?
Chapter 1 Solutions
Student Workbook With Lab Manual For Fletcher's Residential Construction Academy: House Wiring, 5th
- Directions: Circle T to indicate true statements or F to indicate false statements. The higher the resistance in an electrical circuit, the lower the amount of current that can flow in the circuit. (Objective 1-2)arrow_forwardA ground resistance meter is used to determine the amount of resistance__________.(Objective 4-7) a. through a grounding electrode to the earth b. though a grounding electrode to the metal frame of an electrical cabinet c. from one end of a grounding conductor to the other end d. from a grounded conductor to the eartharrow_forwardThe range of a projectile is 4 times its maximum height, and it remains in the air for 2 sec. two a) At what angle was it launched? b) What was the initial speed? c) What is the scope?arrow_forward
- a. Solve for Vicat time of setting. b. Solve for the final time of setting.arrow_forwardFill in the blanks a) b) -1 attachment - 2. Situation: You and your family are watching fireworks display for New Year's Evey The first rocket was launched with an initial velocity of 165 m/s, while the second rocket was launched t seconds later acquiring the same initial velocity. The two rockets are set to explode at the same time at 5e0 m above the ground, just when the first rocket is falling and the second rocket is rising. Determine: a. The time, t b. The velocity of the first rocket at the time of explosionarrow_forwardplease identify the correct answer, thanks!arrow_forward
- Modular Questions M7-1 DIFFERENTIAL LEVELING. Preparing and complete the differential level notes for the information shown in the accompanying figure. Include the customary arithmetic check. Levellng Rod Leveling Rod 3.90 (BS) HI4 0.35 (FS) BM 0.68 HI BS) 3.75 (FS) HIz 3.73 (BS) 1.64 (FS) H2 3.52 SP. 0.98 BM. (Elev 125.45m) (BS) (FS) TP TP2 M7-2 PROFILE LEVELING. Figure shows a schematic arrangement of a profile level route from BM33 to BM34. The values indicated represent backsight, foresight, and intermediate foresight readings taken on stations along the route. Prepare and complete profile level notes for the portrayed information. Show the customary arithmetic check and plot the profile. 2+00 1+ 00 3.06 (FS) IFS 03+00 1.7 IFS) 3.43 (FS) TP, 4+40 6+ 00 HI, 22 5+00 8+00 2.8 IFS) HIz 2.45 (FS) BM, M33 BM. "34 Elev 328.7Om 9+00 Il+00 10+00 M7-3 TRIGONOMETRIC LEVELING. A vertical angle of -12°25' is measured to the top of a water tank from an instrument set up on a hill 585.00 meters…arrow_forward4 - kindly identify the correct answer, thanks!arrow_forwardPlease show the complete step-by-step solution. Choose the answer from the choices below. I’ll rate you with an upvote later. Thank you.arrow_forward
- Residential Construction Academy: House Wiring (M...Civil EngineeringISBN:9781337402415Author:Gregory W FletcherPublisher:Cengage LearningSolid Waste EngineeringCivil EngineeringISBN:9781305635203Author:Worrell, William A.Publisher:Cengage Learning,