Lab Manual for Smith's Electricity for Refrigeration, Heating, and Air Conditioning, 9th
9th Edition
ISBN: 9781285180014
Author: Russell E. Smith
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 1, Problem 16RQ
An electrical device that will open an electrical circuit, preventing current flow to the circuit if a small leak to ground is detected, is called a _________.
- a. GFCI
- b. common circuit breaker
- c. fuse
- d. receptacle
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
2.A. You can usually check for a leak in a vacuum system by looking at or feelingA. at the exhaust of the vacuum pump.B. at the vacuum gauge at the vacuum pump.C. for signs of dirt on the piping.
2.B. When you measure the voltage drop across a set of contacts, you'reA. checking the quality of the contact set.B. sensing how much current is flowing in the circuit.C. measuring the equivalent motor resistance.
2.C. A chain-drive system can be aligned easier than a belt-drive system since the chain-drive systemA. can have a string left on the sprockets after the alignment is complete.B. can have the chain removed while the final alignment is taking place.C. is less critical to misalignment.
The type of hazard whereby sparks are generated electrically is called:
Explosion
contact
fires
strain.
Give three(3 each) specific important safety precautions in handling the following gadgets/devices:
1. heater
2. Air conditioner
3. computer system
Chapter 1 Solutions
Lab Manual for Smith's Electricity for Refrigeration, Heating, and Air Conditioning, 9th
Ch. 1 - True or False: A heating and air-conditioning...Ch. 1 - What is a live electrical circuit?Ch. 1 - Which of the following voltages will a...Ch. 1 - Electrical shock occurs when a person _________....Ch. 1 - What are the important elements of electrical...Ch. 1 - Prob. 6RQCh. 1 - Which of the following is the standard by which...Ch. 1 - Prob. 8RQCh. 1 - What type of ladder should the technician use on...Ch. 1 - What precautions should be taken when you see a...
Ch. 1 - True or False: It is recommended that at least one...Ch. 1 - True or False: The correct fuse size for an...Ch. 1 - What is the difference between a two-prong plug...Ch. 1 - Which prong on a three-prong plug is the ground?...Ch. 1 - True or False: A grounding adapter does no good if...Ch. 1 - An electrical device that will open an electrical...Ch. 1 - True or False: Receptacles used on the job site...Ch. 1 - What precautions should you use when working in an...Ch. 1 - What is the difference between a fuse and a...Ch. 1 - List at least five electrical safety rules that...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The ________is both the greatest asset and the greatest liability of an electronic leak detector.arrow_forwardWhy does a system need to be maintained?arrow_forwardhile discussing NTC thermistors; Technician A says that some systems use this type of thermistor as a protection device. Technician B says that when there is high current in a circuit, the resistance of the thermistor increases and causes a decrease in current flow. Who is correct?arrow_forward
- vibration absorbers is not true? C. The end of the vibration absorber farthest from B. Vibration absorbers should be installed vertically &Which of the following statements regarding V Vihration absorbers can be placed on either side s. the compressor. whenever possible. the vibration source should be secured. D. Vibration absorbers should be insulated if they are installed in a suction line that is below 32°F (0°C).arrow_forwardTechnician A says that installing a thermostat incorrectly can cause the housing to break. Technician B says that it is OK to install a thermostat in either direction. Who is correct? Select one: a. Technician A only b. Technician B only C. Both A and B d. Neither A nor Barrow_forwardThe following transducer is used to measure the temperature. a. Bourdon tube b. Bellows c. Thermocouple d. Strain Gaugearrow_forward
- Wiring harnesses are typically shielded by plasticconduit. What color is normally used to shield SRSrelatedwiring?a. Blackb. Greenc. Yellowd. Orangearrow_forwardWhat is thermocouple gauge used for detection of leaks in vacuum systems.arrow_forwardLockout may involve: Opening a disconnect switch. b. Closing a valve. Placing a block in the equipment. d. All of the above. a. C.arrow_forward
- An overheating vehicle is being discussed. Technician A states that the vehicle may be overheating because the heater control valve is stuck closed. Technician B states that the vehicle may be overheating because the PCM in not energizing the cooling fan relay. Who is correct? Select one: a. Technician A only b. Technician B only c. Both Technicians A and B d. Neither Technician A nor Barrow_forwardTrue or False: Pressures below atmospheric pressure cannot be detected.arrow_forwardWhat is a standpipe?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Understanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning
General Industrial Safety; Author: Jim Pytel;https://www.youtube.com/watch?v=RXtF_vQRebM;License: Standard youtube license