A, -daB |P2 - fBC PROBLEM 1.4-1

Q: The flat bars shown in parts a and b of the figure are subjected to tensile forces P-3.0 kips. Each…

A: Given data,       Tensile force  P=3.0 Kips       Thickness      t=0.3 in.a  For the bar with a…

Q: The three-member frame has original dimensions as shown in the figure. Elements F-D-B and A-B-E are…

A: givenElement FDB and ABE are rigid. so axial and flexure deeflection is zero.Area of CD…

Q: 3.40-3.41 For the space trusses shown in Figures P3-40 and P3-41, determine the nodal dis-…

A:

Q: F1. The rigid bar ABC in the figure is supported by a clevis and pin at its right hand side and by…

A: Draw the free-body diagram of the beam.

Q: Let's load a 1500 kg load on a platform with its own weight of 500 kg as shown in the figure. This…

A: Given data: Mass of the load, mL = 1500 kg. Mass of the platform, mp = 500 kg. The number of rods,…

Q: A pole is fixed at the base and is subjected to a linearly varying distributed force with maximum…

A:

Q: 2.10-3 A flat bar of width b and thickness 1 has a hole of diameter d drilled through it (see…

A: Given data: -  The width of the bar is b. The thickness of the bar is t. The diameter of the hole…

Q: For the assembly shown in Figure.(5). If the stress in the steel rod become (120+b) Mpa when the…

A:

Q: sembly consisting of two inclined bars, as shown in the figure.  The cross-sectional area of bar (1)…

A:

Q: The rigid bar ABC shown in the figure is hinged at A and supported by a steel rod at B. Determine…

A: Given data as per the question stress in steel bar =30 ksivertical moment of C =0.10 inlength of…

Q: The assembly shown in the figure consists ofa brass core (diameter d1 = 0.25 in.) surrounded by…

A: Given Data The diameter of the brass core is: d1=0.25 in The inner diameter is: d2=0.28 in The…

Q: EXAMPLE: 4. A 2-in.-diameter steel tube with a wall thickness of 0.05 inch just fits in a rigid…

A:

Q: The rectangular bar is connected to the support bracket with a circular pin, as shown in the figure.…

A: To Find :  The average bearing stress produce in the bar .  Given :  The width is w=2.25 in. The…

Q: A cantilevered structure has dimensions L=65-in, L-9.5-in, L=6.2-in, LF3.8-in and diameter d=2.5-in.…

A: Given L1 = 65 in L2= 9.5 in L3 = 6.2 in  L4 = 3.8 in  d1 = 2.5 in Fy = 78 lb Fz = 153 lb We have to…

Q: 3. Work problem 2.9-2 from the textbook, which is as follows. The prismatic bar in the figure is…

A:

Q: The pinned joint shown in the figure below is held by a ¾-in-diameter pin at A. If the force P = 5…

A: Given data :- diameter= 3/4 in Force(P) =5kips Thickness =1 in

Q: Calculate the bearing capacity for a 2 * 3 rectangular foundation that is kN under eccentric load as…

A:

Q: A high-strength steel bar used in a large cranehas a diameter d = 2.00 in. (see figure). The steel…

A:

Q: Problem No. 2. A 150-mm-wide steel bar with a butt-welded joint, as shown. SET LOAD P NORMAL STRESS…

A: Given DataP=205kNσn=80MPaτ=40MPaθ=57{taken} C section taken for computing the minimum thickness

Q: A horizontal load Pis applied to an assembly consisting of two inclined bars, as shown in the…

A:

Q: A horizontal load Pis applied to an assembly consisting of two inclined bars, as shown in the…

A:

Q: See the figure below. AD is a member with varying diameters. There are three axial loads applied at…

A: Given data: The magnitude of the force acting at the point B is; F1=10 lbs. The magnitude of the…

Q: The rigid beam BC shown in the figure is supported by rods (1) and (2) that have cross-sectional…

A: Given:A1=175 mm2A2=300 mm2w=16 KN/mL=2.8 ma=1.7 m

Q: For the truss shown below, use symmetry to determine the displacement of the and the stresses in…

A:

Q: Q.2) For the figure shown, if a load P₁ = 120 kN at A and load P₂ 100 kN is uniformly distributed…

A: Given:Find:Poisson's ratio for the pipe material.

Q: Q4\ A filleted. plate of thickness t supports an axial load P (Figure below). Determine the diameter…

A:

Q: For the assembly shown in Figure.(5). If the stress in the steel rod become (120+b) Mpa when the…

A:

Q: 1. Determine stress distributions of a rotating ring (See the figure below; Angular speed: @; Mass…

A: Write the given data. Angular speed: ωMass density: ρOuter radius: Ro=bInner radius: Ri=a

Q: A tensile load of 6 kN at 25 C was applied to a steel rod stretching between two rigid walls as…

A: Given: F= 6 kN T=25°Cα=12.2 μm/(m°C)E=200 GPaσ=150 MPa

Q: Current Attempt in Progress A rectangular bar having width w = 6.25 in. and thickness t= 1.25 in. is…

A:

Q: Asimple pin-connected truss is loaded and supported as shown in the figure. All members of the truss…

A:

Q: -15 m---25 m- - 3 m B 35 m 784,8 kN 15 m

A:

Q: QI A rigid bar ABCD is pinned at end A and supported by two cables of equal length at points B and C…

A:

Q: The rigid beam BC shown in Figure is supported by rods (1) and (2) that have cross-sectional areas…

A:

Q: Find the stresses and compressions in each section of the composite member shown in Figure. Use Es-…

A:

Q: Solve the problem stated below. Use bond papers and black ball pen. Make your solution clear and…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.