(a)
The current in given resistor using ohm’s law.
(a)

Answer to Problem 1.1P
Explanation of Solution
Given:
Calculation:
According to ohm’s law, the formula of current flowing through a resistor is given by
Plugging given values:
(b)
The resistance for given values of current and voltage using ohm’s law.
(b)

Answer to Problem 1.1P
Explanation of Solution
Given:
Calculation:
According to ohm’s law, the formula of resistance is given by
Plugging given values:
(c)
The voltage for given values of current and resistance using ohm’s law.
(c)

Answer to Problem 1.1P
Explanation of Solution
Given:
Calculation:
According to ohm’s law, the formula of current flowing through a resistor is given by
Plugging given values:
(d)
The current for given values of voltage and resistance using ohm’s law.
(d)

Answer to Problem 1.1P
Explanation of Solution
Given:
Calculation:
According to ohm’s law, the formula of current flowing through a resistor is given by
Plugging given values:
Want to see more full solutions like this?
Chapter 1 Solutions
MICROELECTRONIC CIRCUITS W/LAB MAN >P<
- = = For the circuit shown, let V, 15 V, I, 4A, R₁ =5, R₂ 10, R3 10, and R4 5. Determine the output voltage Vo as follows All resistor values are in ohms. 1. Identify the supermesh and write its corresponding Mesh equation. Provide your expression in terms of the shown mesh current i₁, and 12 of the form (R11 · 11+ R12 · 12 = V₁), then enter the corresponding values: R11 Ω R12 V₁= V Ω 2. Use the above equation, and supermesh inner expression to calculate i₂: i₂- Find Vo V₁ = A V R₁ www M R3 ww V R4 V₁ 0 IS R₁ The relative tolerance for this problem is 7 %. 0arrow_forward11.18 In the circuit of Fig. P11.18, what should the value of thecoupling coefficient k be so that Vout/Vin = 0.49?arrow_forward11.26 Determine the complex power supplied by the source inthe circuit of Fig. P11.26.arrow_forward
- 11.23 Determine Vout in the circuit of Fig. P11.23arrow_forwardReversing 1⏀ Motors-all the wires are not used. Use the data sheet b on page 383 to draw the wiring diagram. Note: interchange the red and black leads to reverse the motor rotation. Use only the number of contacts required. Insulate any motor wire not used with a wire nut. Wire the motor to operate in forward and reverse at 115 VACarrow_forwardSee both images to answerarrow_forward
- See both images to answerarrow_forwardAn inner-city electric bus with 7,200kg weight and average speed of 72 km/hour operates using a hybrid power source of lithium-ion battery pack and a bank of super capacitor. equipped with a lithium battery pack and a bank of supercapacitor. The energy content of the supercapacitor bank is twice the regenerative breaking energy of the electric bus at average speed. The electric bus commutes 490 km per charged battery and consumes 400 Wh/km. Design the supercapacitor bank to provide 100V output, based on supercapacitor cells with 3600F capacitance and 2V. Calculate the energy density of the supercapacitor at the cell level, assume cells with 10cm diameter and 15 cm height. 3. Design the battery pack for the electric bus by assuming that the energy of regenerative breaking will not be used for commuting but used to run the vehicle’s accessories. The unit cell of the battery pack is a lithium-ion…arrow_forwardA rod coincident with the z-axis extends from 0 to -L. If the rod carries a uniform charge density of pL (a) calculate the electric field intensity at a point h on the z-axis. (b) Use your answer to show that when h>>L the rod behaves as a point charge of value plL . (c) How much larger than the length of the rod must h be in order that the answer to part b) is a reasonably accurate estimate.arrow_forward
- The separation of two point charges with charges Q1=36pC and ,Q2=9pC respectively, is 3 cm. If a third point charge Q3 is placed on the line joining Q1 and Q2 at a distance d from Q1 find Q3 and d that ensures that the force on all charges is zero.arrow_forward5. The electric field on the positive z-axis due to a uniformly charged disk of radius a that lies in the x-y plane with center at the origin is claimed to be given by - Ps Z 2E 2 a² + z² Where ps is the surface charge density on the disk. Without deriving this formula, evaluate it for its probable correctness. (a) Is its symmetry correct? Explain. (b) If z>> a, it reduces to that of a point charge of value a²ps (c) if z> z is large the formula reduces to that of an infinite plane.arrow_forwardA rod coincident with the z-axis extends from 0 to L. If the rod carries a uniform charge density of pL , calculate the electric field intensity at a point h on the y-axis.arrow_forward
- Introductory Circuit Analysis (13th Edition)Electrical EngineeringISBN:9780133923605Author:Robert L. BoylestadPublisher:PEARSONDelmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage LearningProgrammable Logic ControllersElectrical EngineeringISBN:9780073373843Author:Frank D. PetruzellaPublisher:McGraw-Hill Education
- Fundamentals of Electric CircuitsElectrical EngineeringISBN:9780078028229Author:Charles K Alexander, Matthew SadikuPublisher:McGraw-Hill EducationElectric Circuits. (11th Edition)Electrical EngineeringISBN:9780134746968Author:James W. Nilsson, Susan RiedelPublisher:PEARSONEngineering ElectromagneticsElectrical EngineeringISBN:9780078028151Author:Hayt, William H. (william Hart), Jr, BUCK, John A.Publisher:Mcgraw-hill Education,





