You would like to calculate some HVAC properties related to moist air. Two types of thermometers are available to you: regular thermometer that is set in the shade at a certain height above the ground, and a psychrometer (or a wetted thermometer). If the measured dry bulb temperature is 23 °C and the wet bulb temperature is measured at 14 °C. Assume you are at an elevation of 1000 m above sea level: a. What is the partial pressure of water vapor in the air? b. What is the relative humidity? c. What is the humidity ratio?

You would like to calculate some HVAC properties related to moist air. Two types of thermometers are available to you: regular thermometer that is set in the shade at a certain height above the ground, and a psychrometer (or a wetted thermometer). If the measured dry bulb temperature is 23 °C and the wet bulb temperature is measured at 14 °C. Assume you are at an elevation of 1000 m above sea level: a. What is the partial pressure of water vapor in the air? b. What is the relative humidity? c. What is the humidity ratio?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

AMNT 280 Assignments 1-4 Media Presentation Categories Of Reciprocating Engines Develop a Media Presentation develop a power point media presentation Presentation will require researching a module specific topic For this activity you will research the four categories of reciprocating engines In your presentation address the following: 1 Research the four different types of reciprocating engines2 Provide an overview of the design, construction, and firing order of each engine 3 Provide research concerning which air frame used the engine Presentation Guidelines Note:This information applies to all Media Presentation activities and will not be repeated Present your research material in the format of a written document (Introduction, body, and conclusion) Presentation requirements consist of 5-7 slides with a balance of both bullet text information and images; does not include the title or reference slide APA formatting and structural guidelines apply Additional information…
Question 6 a) The bore of each cylinder in a six-cylinder car engine is 45 mm and the stroke for each piston is 125 mm. calculate the cubic capacity of the engine in cubic centimetres (cm³); and calculate the clearance volume per cylinder for a compression ratio, r, of 8.75. b) The bore of each cylinder in a four-cylinder four-stroke internal combustion engine is 38 mm and the stroke of each piston is 165 mm. During testing, the engine runs at 180 revolutions per minute (rpm) with a pressure-volume indicator diagram showing a mean net area of 3.4 cm² and a diagram length of 1.2 cm. The pressure scale on the indictor diagram is set to 150 kN/m² per cm. Calculate the mean effective pressure (m.e.p) and the indicated power developed by this four-cylinder four-stroke engine. c) Figure Q6c shows a pulley system with a suspended load w of 2000 N. Calculate the following: (i) (ii) (iii) (iv) The effort force (FEffort) necessary to lift and hold a load of 2000 N. The ideal mechanical advantage…
IL IOUJOICIICA RAGICated in the 2-Dirmensional views (Orthographic) is milimeters centimeters There is no way of teling meters 3. When yow stari investigating to salve technological problems the following Technologiool Process yes can be followed to find information: Compare exising products write o design brief perform practical tests both A and C plus collect data. 4.Jocolleci dota the folowing could be used as a resource: Sractical investigation and testing of oproduct A, Band C A speok to or inteniew people firnd infomclion irom any print medio 6. existing products will help technologists in 20
Define the international system of units.
None
12
Question 3 10 points V Sav The basic principle to select a material for a product is to use a material with properties that meet or exceed the product performance requirements, and keep the cost of the product as low as possible to use a material with properties that meet the product performance requirements, and keep the cost of the product as low as possible to use a material with properties that exceed the product performance requirements as much as possible, and keep the cost of the product as low as possible to use a material with properties that meet or exceed the product performance requirements, and keep the cost of the material as low as possible
1A
please provide a clear solution and FBD. please answer within 30 minutes, thank you!
Q/ Correct the under line words 14. Al-4%. Mg alloys are produced by extrusion because has high strength 15. Mg -Zn - Zr alloy is not proper to produce by extrusion because of susceptible to micro porosity and can be used for casting process 16. Brass-alloys are expensive because of difficulties experienced of its casting 17. The density, T.S. and hardness of Fe alloys can be decreased by working
Define the following Symbols: A, Ag, Ix, L, T, rT, ksi, MPa
use 3 sig figs pls