You titrated HCl with 0.866 M NaOH and you wrote the initial and final volume of NaOH used in the titration. Using 25.0 mL of HCl as the volume of the unknown HCI, calculate the molarity of HCI Trial Initial volume of NAOH Final volume of NaOH 1 50.0 mL 24.3 mL 2 24.3 mL 0.300 mL 3 48.0 mL 25.5 ml

You titrated HCl with 0.866 M NaOH and you wrote the initial and final volume of NaOH used in the titration. Using 25.0 mL of HCl as the volume of the unknown HCI, calculate the molarity of HCI Trial Initial volume of NAOH Final volume of NaOH 1 50.0 mL 24.3 mL 2 24.3 mL 0.300 mL 3 48.0 mL 25.5 ml

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

What’s the answer in M
An HCl solution was titrated to determine its concentration using 15.00 mL 0.02500 M sodium carbonate standard solution. It required exactly 20.000 mL acid to completely neutralize the reaction between the titrant and analyte. What is the concentration of HCl solution? a 0.06667 M b 0.03750 M c 0.01875 M d 0.03333 M
20. Consider the following hypothetical acid-base titration where A represents the acid and B represents the base. The products of this reaction are salt and water. Assume the equation is balanced as written. 3A + 2B --> salt + water (OR 3 A + 2 B right arrow salt + water) Two burets are setup with one containing acid, A, and the other containing base, B. The initial volume of buret A is 1.32 mL and the initial volume of buret B is 1.14 mL. Acid from buret A is added to a flask until the final volume of buret A is 12.10 mL. Base from buret B is added to the flask until the titration reaches the endpoint. The final volume of buret B reads 24.96 mL. Calculate the molarity of the acid, A, if the base has a molarity of 1.213 molar. You may want to create a data table to help you organize your work. Do not type units with your answer.
A solution contains Cr3+ and Mg2+. The addition of 1.00 L of 1.53 M NaF solution is required to cause the complete precipitation of these ions as CrF3(s) and MgF2(s). The total mass of the precipitate is 50.0 g . Find the mass of Cr3+ in the original solution.
A student needs to dilute a 0.40 M Pb(NO3)₂ solution to make 75.0 mL of 0.16 M Pb(NO3)2. Set up the calculation by placing the values with the correct units into the equation. Then, calculate the volume, in milliliters, of the 0.40 M Pb(NO3)₂ solution that is needed. 75.0 mL 75.0 L Answer Bank 0.40 M 0.16 mL 0.16 M 0.40 mL = mL
An aqueous solution of barium hydroxide is standardized by titration with a 0.180 M solution of hydrochloric acid.If 28.0 mL of base are required to neutralize 26.4 mL of the acid, what is the molarity of the barium hydroxide solution?
A 0.430 g sample of a monoprotic acid is dissolved in water and titrated with 0.110 M KOH. What is the molar mass of the acid if 31.0 mL of the KOH solution is required to neutralize the sample? molar mass: g/mol **** -0 -1 2 -3 -4 6 -7 9 10 11 12 13 15 16 17 18 19 20 -21 22 23
To determine the molarity of an unknown sulfuric acid solution in a titration, a standardized NaOH solution with a molarity of 0.138 M was given. A student used 11.8 mL of the NaOH solution to reach to the end point of the titration with a 25.0 mL sample of the unknown acid solution. What is the molarity of the unknown sulfuric acid solution?
Consider the titration of 25.00 mL of Sprite with 0.053 M NaOH. Using the following data, determine the citric acid concentration in Sprite (g/L). Take the molar mass of citric acid to be 192.124 g/mol. Give your answer to one decimal place. initial volume (mL) final volume (mL) Your Answer: Answer Buret reading (mL) 1.64 14.52
The titration below was performed by placing 10.00 mL solution in an Erlenmeyer flask and titrating it with 0.1000 M HCl. What is the concentration of the solution being titrated? 0.02500 M 0.0500 M 0.0750 M 0.100 M 0.200 M
If the initial volume reading for the first titration was 0.16 mL and the final volume reading was 11.68 mL, what volume of iodine solution was used in your first titration (in mL)? Include the unit in your answer and two decimal places in your answer.
A student is given the following labeled solutions: NaCl, AgNO3, FeCl2, HCI, and KaCo The data was collected and summarized in the following table. The student then receives 5 test tubes labeled A, B, C, D, and E, which contain the five solution above. Data collect after mixing these solutions are given in the second table below. 4. FeCl2 HCI NaCI AGNO, Precipitate Şolution K;CO, Precipitate Gas forms No reaction XXXXX forms K½CO; forms XXXXX Precipitate Precipitate Precipitate Precipitate XXXXX XXXXX AgNO; forms forms forms forms Precipitate No Reaction No reaction XXXXX XXXXX NaCl No reaction forms Precipitate No reaction ХXXXX XXXXX Precipitate No reaction FeCl forms forms Precipitate No reaction No reaction HCI Gas forms XXXXX forms XXXXX Solution A B D A XXXXX No reaction Precipitate Precipitate No reaction XXXXX forms forms B No reaction XXXXX Gas forms Precipitate No reaction XXXXX forms C Precipitate Gas forms Precipitate No reaction XXXXX XXXXX forms forms Precipitate…