, You pull downward with a force of 28 N on a rope that passes over a disk shaped pulley of mass 1.2 kg and radius 0.075 m. The other end of the rope is attached to a 0.67 kg mass. a) Is the tension in the rope the same on both sides of the pulley? If not, which side has the largest tension? b) Find the tension in the rope on both sides of the pulley. (a: not same, b: 28 N on your side, 18 N)

, You pull downward with a force of 28 N on a rope that passes over a disk shaped pulley of mass 1.2 kg and radius 0.075 m. The other end of the rope is attached to a 0.67 kg mass. a) Is the tension in the rope the same on both sides of the pulley? If not, which side has the largest tension? b) Find the tension in the rope on both sides of the pulley. (a: not same, b: 28 N on your side, 18 N)

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

An m 10.8kg mass is attached to a cord that is wrapped around a wheel of radius r= 11.9cm (see the figure below). The acceleration of the mass down the frictionless incline is measured to be a = 2.17m/s^2. Assuming the axle of the wheel to be frictionless, and the angle to be 8 = 36.5deg determine the tension in the rope. Submit Answer Tries 0/10 m Determine the moment of inertia of the wheel. ) Submit Answer Tries 0/10 Determine angular speed of the wheel 2.09s after it begins rotating, starting from rest.) Submit Answer Tries 0/10
At what maximum speed can a car manage a turn on a wet, level road with coefficient of static friction 0.230 without sliding out of control? The radius of the turn is 25.0 m
Two masses are connected by an ideal rope over a pulley. The rope has no mass or stretch. The pulley is frictionless but has mass Mp and radius R. M, is on an approximately frictionless slope with angle 0 =19°. %3D The masses are all equal, M1 = M2 Mp. %3D The pulley can be approximated by a hoop with I = Mp R2 %3D If the masses are released from rest (not moving), what is their speed after M2 has fallen a distance h = 2.4 m?
Consider the setup shown below. The blocks have masses 3.6 kg and 24 kg. The pulley has mass 7.4 kg, and is a uniform disc with radius 0.23 m. Assume the pulley to be fric- tionless, but the coefficient of friction between the block and the surface is 0.36. a T2 3.6 kg T1 = 0.36 22° 24 kg What is the acceleration of the blocks? As- sume the 24 kg mass is descending with accel- erațion a. The moment of inertia of the disk is - M R? and the acceleration of gravity is 2 9.8 m/s?. Answer in units of m/s?.
An Atwood's machine consists of blocks of masses m₁ = 13.0 kg and m₂ = 24.0 kg attached by a cord running over a pulley as in the figure below. The pulley is a solid cylinder with mass M = 7.60 kg and radius r = 0.200 m. The block of mass m., is allowed to drop, and the cord turns the pulley without slipping. M T2 Q (a) Why must the tension 7₂ be greater than the tension 7₁? This answer has not been graded yet. (b) What is the acceleration of the system, assuming the pulley axis is frictionless? (Give the magnitude of a.) m/s² (c) Find the tensions T, and T₂. T₁ = T2₂ =
A block of mass 2 kg slides down an inclined plane at an angle of 45° with a massless tether attached to a pulley with mass 3 kg and radius 0.7 m at the top of the incline (see the following figure). The pulley can be approximated as a disk. The coefficient of kinetic friction on the plane is 0.2. What is the acceleration of the block (in m/s²)? (Enter the magnitude.) 3.59 45° x m/s²
Two mass (m1 = 6.35 and m2 = 5.31) are attached by a massless string over a pulley on a table (uk = 0.167). The pulley is a disk (mass = 2.35 and radius 0.36). Find the acceleration of the system.
a. What is the magnitude of acceleration of the block? b. What is the magnitude of the tension force from the block on the cylinder?
Two buckets of mass ?1=17.5 kg and ?2=15.1 kg are attached to the ends of a massless rope which passes over a pulley with a mass of ?p=8.53 kg and a radius of ?p=0.450 m. Assume that the rope does not slip on the pulley, and that the pulley rotates without friction. The buckets are released from rest and begin to move. If the larger bucket is a distance ?0=2.05 m above the ground when it is released, with what speed ? will it hit the ground?
Can you also double check the answer. Thank you in advance
Please help: A 2.90 kg bucket is attached to a disk-shaped pulley of radius 0.131 m and mass 0.792 kg. If the bucket is allowed to fall, How far does the bucket drop in 1.20 s?
= - = 6. A mass M₁ 10 kg resting on a horizontal frictionless surface is attached to a M₂ = 7 kg weight by a light wire that passes over a frictionless pulley. See figure. The pulley has the shape of a uniform disk of mass M3 4 kg and radius R 0.3 m. After the system is released, find (a) the tension in the wire on both sides of the pulley, (b) the acceleration of M₁, and (c) the horizontal and vertical forces that the axle exerts on the pulley. M1 M 3 M2