6. A mass M₁ 10 kg resting on a horizontal frictionless surface is attached to a M₂ = 7 kg weight by a light wire that passes over a frictionless pulley. See figure. The pulley has the shape of a uniform disk of mass M3 = 4 kg and radius R = 0.3 m. After the system is released, find (a) the tension in the wire on both sides of the pulley, (b) the acceleration of M₁, and (c) the horizontal and vertical forces that the axle exerts on the pulley. M1 M3 M₂

6. A mass M₁ 10 kg resting on a horizontal frictionless surface is attached to a M₂ = 7 kg weight by a light wire that passes over a frictionless pulley. See figure. The pulley has the shape of a uniform disk of mass M3 = 4 kg and radius R = 0.3 m. After the system is released, find (a) the tension in the wire on both sides of the pulley, (b) the acceleration of M₁, and (c) the horizontal and vertical forces that the axle exerts on the pulley. M1 M3 M₂

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A jewel smith wishing to buff a finished piece of jewelry attaches a buffing disk to his drill. The radius of the disk is 4.30 mm, and he operates it at 2.50 104 rad/s. (a) Determine the tangential speed, in m/s, of the rim of the disk. m/s (b) The jeweler increases the operating speed so that the tangential speed of the rim of the disk is now 280 m/s. What is the period of rotation, in seconds, of the disk now? s
In the figure, two 7.60 kg blocks are connected by a massless string over a pulley of radius 1.30 cm and rotational inertia 7.40 x 104 kg-m2. The string does not slip on the pulley; it is not known whether there is friction between the table and the sliding block; the pulley's axis is frictionless. When this system is released from rest, the pulley turns through 1.20 rad in 154 ms and the acceleration of the blocks is constant. What are (a) the magnitude of the pulley's angular acceleration, (b) the magnitude of either block's acceleration, (c) string tension T, and (d) string tension T? Assume free-fall acceleration to be equal to 9.81 m/s?.
An Atwood's machine consists of blocks of masses m₁ = 13.0 kg and m₂ = 24.0 kg attached by a cord running over a pulley as in the figure below. The pulley is a solid cylinder with mass M = 7.60 kg and radius r = 0.200 m. The block of mass m., is allowed to drop, and the cord turns the pulley without slipping. M T2 Q (a) Why must the tension 7₂ be greater than the tension 7₁? This answer has not been graded yet. (b) What is the acceleration of the system, assuming the pulley axis is frictionless? (Give the magnitude of a.) m/s² (c) Find the tensions T, and T₂. T₁ = T2₂ =
In the figure, a uniform sphere of mass m = 0.551 kg and radius r = 0.139 m is held in place by a massless rope attached to a frictionless wall a distance L = 2.31 m above the center of the sphere. Find (a) the tension in the rope and (b) the force on the sphere from the wall.
A weight of mass 1.32 kg is suspended by a string wrapped around a pulley wheel, which consists of a solid disk of mass 4.47 kg and radius 1.03 m. The system is released from rest. Over what vertical distance does the hanging mass move in 3.0 seconds? Ignore friction and drag forces, and assume that the string does not slip. Hint: If the string had 0 length, it would be obvious that the point mass contributes Ipt = mR² to the total rotational inertia, since the point mass would be directly stuck on the outside of the pulley. What's the difference if the string has nonzero length, so that the point mass hangs below the pulley as in the diagram? None at all! The pulley can't tell the difference between a point mass attached to it by a 0 length string or a 20 meter long string. All it knows is that there's a point mass m attached to its outer edge.
A jewel smith wishing to buff a finished piece of jewelry attaches a buffing disk to his drill. The radius of the disk is 4.10 mm, and he operates it at 2.25 104 rad/s. (a) Determine the tangential speed, in m/s, of the rim of the disk. m/s (b) The jeweler increases the operating speed so that the tangential speed of the rim of the disk is now 285 m/s. What is the period of rotation, in seconds, of the disk now? s
A uniform disk of radius 0.507 m and unknown mass is constrained to rotate about a perpendicular axis through its center. A ring with the same mass as the disk is attached around the disk's rim. A tangential force of 0.243 N applied at the rim causes an angular acceleration of 0.117 rad/s^2. Find the mass of the disk.
In the figure, two 5.70 kg blocks are connected by a massless string over a pulley of radius 140 cm and rotational inertia 7.40 x 104 kg-m². The string does not slip on the pulley: it is not known whether there is friction between the table and the sliding block; the pulley's axis is frictionless. When this system is released from rest, the pulley turns through 1.20 rad in 126 ms and the acceleration of the blocks is constant. What are (a) the magnitude of the pulley's angular acceleration, (b) the magnitude of either block's acceleration, (c) string tension T, and (d) string tension T;? Assume free-fall acceleration to be equal to 9.81 ms?. (a) Number Units (b) Number Units (c) Number Units (d) Number Units >
A string is wrapped many times around a pulley and is connected to a block with mb = 4.641 kg that is hanging vertically. The pulley consists of a wheel of radius 43.11 cm and mass mp constructed with spokes that have negligible mass. What is the magnitude of the acceleration of the block? Submit Answer Tries 0/99 6.455 kg тр ть
Am1= 19.0-kg object and a m 2 = 9.0-kg object are suspended, joined by a cord that passes over a pulley with a radius of R = 30.0 cm and a mass of M = 3.00 kg as seen in the Figure. The cord has a negligible mass and does not slip on the pulley. The pulley rotates on its axis without friction. The objects start from rest d = 5.00 m apart. Treat the pulley as a uniform disk, and determine the speeds of the two objects as they pass each other. (Your result must be in units of m /s and include 2 digit after the decimal point. Maximum of 4% of error is accepted in your answer. Take g = 9.80 m/s 2.) Hint: For solid cylinder of disk the moment of inertia about an axis through center of mass is IcOM = MR %3D d.
In the figure, two 6.30 kg blocks are connected by a massless string over a pulley of radius 1.30 cm and rotational inertia 7.40 x 104 kg-m2. The string does not slip on the pulley; it is not known whether there is friction between the table and the sliding block; the pulley's axis is frictionless. When this system is released from rest, the pulley turns through 0.800 rad in 126 ms and the acceleration of the blocks is constant. What are (a) the magnitude of the pulley's angular acceleration, (b) the magnitude of either block's acceleration, (c) string tension T,, and (d) string tension T,? Assume free-fall acceleration to be equal to 9.81 m/s. (a) Number Units (b) Number Units (c) Number Units (d) Number Units
In figure, two 7.30 kg blocks are connected by a massless string over a pulley of radius 1.80 cm and rotational inertia 7.80 x 10-4 kg.m2. The string does not slip on the pulley; it is not known whether there is friction between the table and the sliding block; the pulley axis is frictionless. When this system is released from rest, the pulley turns through 0.560 rad in 89.0 ms and the acceleration of the block is constant. What is the magnitude of the pulley's angular acceleration? (Your result must be in units of rad /s2 and include 1 digit after the decimal point. Maximum of 2% of error is accepted in your answer.) T R, I T M