You begin preparation of the calibration curve to measure absorbance vs concentration of FeSCN2+. To do so, you add 1.58 mL of 0.200 M Fe(NO3)3 to a cuvette and then directly add 316 µL of 0.001 M KSCN. What is the resulting concentration of FeSCN²+, assuming complete conversion of SCN¯ to FeSCN²+´ Enter your answer in units of mM to four digits after the decimal.

You begin preparation of the calibration curve to measure absorbance vs concentration of FeSCN2+. To do so, you add 1.58 mL of 0.200 M Fe(NO3)3 to a cuvette and then directly add 316 µL of 0.001 M KSCN. What is the resulting concentration of FeSCN²+, assuming complete conversion of SCN¯ to FeSCN²+´ Enter your answer in units of mM to four digits after the decimal.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

The pH of a solution is 5.84 + 0.05. What is the concentration of Ht in the solution and its absolute uncertainty? [H*] = 1.45 х10-6 0.167 x10-6 M M Incorrect
If the pH of a solution is 2.78 with an absolute uncertainty of ±0.05, what is the [H+] and its uncertainty? O [H+] = 1.66 x 10-3 M uncertainty in the concentration O [H+] = 1.66 x 10-3 M uncertainty in the concentration O [H+] = 1.34 x 10-4 M uncertainty in the concentration 1.78 x 10-5 M O [H+] 1.33 x 10 M -4 uncertainty in the concentration= 1.91 x 10-4 M -1.25 x 10-5 M 1.65 x 10-5 M
If you use [KMnO4]=0.0252 M, Concentration of FeSO4 7 H2O = 5.70 g/L Using a 100-mL graduated cylinder, 50 mL sample of FeSO4*7 H₂O will be measured out. To each sample of FeSO4 7 H2O, add 10.0 mL of H2SO4 and 10 mL of H3PO4 Concentration of SnCl2 2 H2O 2.85 g/mL Using a 100-mL graduated cylinder, 50.0 mL sample of SnCl2 2 H₂O will be measured out. No additional acid is needed. #1 KMnO4 #1 KMnO4 Sample # Initial buret, mL Final buret, mL FeSO4*7 H2O 12.05 21.51 SnCl2 2 H₂O 0.07 9.54 Question) Answer the following questions. b) Determine mol of electron lost per mol of Sn ion. 1) In this case, your answer should be in decimal notation (for example, 0.123, not 1.23*10^-1) with the correct number of significant figures. Also follow the unit specified in each question. Do NOT put its unit in your answer because its unit is shown already in the questions.
Tyler the titrating student did not rinse his buret properly and residual water (not titrant) was left in the buret prior to filling the buret with base. how would the Precision, Accuracy, and Mass of CaCO3 in antacid be affected?
Write a step-by-step procedure for this serial dilution. The stock concentration of the blue dye standard is 1.00 mg/mL. Serial dilution series from the stock standard with the following final concentrations: 500 ug/mL, 250 ug/mL, 125 ug/mL, 62.5 ug/mL. and a blank that is 0ug/ml
Students performed three KHP titrations in Part 1 to standardize their NaOH solution. They reported the following measurements: Determination #1 Determination #2 Determination #3 Mass of KHP + Vial 14.0862 g 14.5621 g 14.3998 g Mass of 'Empty' Vial 13.2492 g 13.7695 g 13.6887 g Final Burette Reading 45.10 mL 38.53 mL 37.17 mL Initial Burette Reading 5.08 mL 0.52 mL 3.19 mL How many moles of NaOH did they use in their first titration? Report your answer to the correct number of significant figures
Which of the options is the right answer ?
mL When blood is donated, sodium oxalate solution is used to precipitate Ca2+, which triggers clotting. A 122.0-mL sample of blood contains 9.70 × 10-5 g Ca A technologist treats the sample with 100.0 mL of 0.1550 M Na₂C₂O. Calculate [Ca2+] after the treatment. Be sure your answer has the correct number of significant figures. Note: Reference the Solubility product constants (Ksp) table for additional information. M Ca2+ 5
You measure 15.0 mL of the H2C2O4 solution with a 100-mL graduated cylinder and add it to a 125-mL Erlenmeyer flask. Then you add two drops of the indicator, phenolphthalein, to the oxalic acid solution in the flask. You dispense the NaOH solution from the buret into the flask (while swirling the flask) until you reach the endpoint. At the endpoint, the solution in the flask turns light pink. You repeat the titration two additional times for a total of three trials. H2C2O4 (aq) + 2 NaOH (aq) --> Na2C2O4 (aq) + 2 H2O (l) (I) (II) (III) Volume of H2C2O4 used 15.00 mL 15.00 mL 15.00 mL how many Moles H2C2O4 are used in each trial?
Please help me with this. THE CORRECT ANSWER IS 0.001958
[B] *refer to the (2) photos below*
The absorbance of a cationic iron(II) sample solution was measured in a spectrophotometer, but the instrument returned an error because the absorbance was too high. The sample was then diluted by using a pipette to take 100.0 μLμL of the sample and injecting it into a cuvette already containing 2.00 mLmL of water (total volume is 2.00 mLmL + 100.0 μLμL). The absorbance value of the diluted solution corresponded to a concentration of 7.71×10−6 M M . What was the concentration of the original solution? Express the concentration to three significant figures with the appropriate units.