You are designing a new eco-friendly thermal coffee mug. It is shaped like a small globe to minimize surface area, which is only about 0.04m^2. You use two 0.003m layers of recyclable PETE which has a thermal conductivity, k, of 0.2W/mK around a 0.01m layer of dead air, with a thermal conductivity of 0.026W/mK. Since this is for hot coffee, use a temperature difference of 40K. Q = Ax (T2-T1) / (R1 + R2 + etc) R =x/k. What is the heat lose through the surface in watts?

You are designing a new eco-friendly thermal coffee mug. It is shaped like a small globe to minimize surface area, which is only about 0.04m^2. You use two 0.003m layers of recyclable PETE which has a thermal conductivity, k, of 0.2W/mK around a 0.01m layer of dead air, with a thermal conductivity of 0.026W/mK. Since this is for hot coffee, use a temperature difference of 40K. Q = Ax (T2-T1) / (R1 + R2 + etc) R =x/k. What is the heat lose through the surface in watts?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.63P

See similar textbooks

Related questions

Q: A modern cabin has a concrete floor that is 4.50 inches thick. A roaring fire keeps the interior of…

Q: 1. A beverage cooler is in the shape of a cube, 42 cm on each inside edge. Its 3.0-cm thick wall are…

Q: A plaster wall which is 20 cm thick with a thermal conductivity of 0.3W/m2 C is used in a certain…

Q: Consider a copper plate that has dimensions of 3 cm x 3 cm x 7 cm (length, width, and thickness,…

A: Given data Dimension of plate = 3cm × 3cm × 7cm Density of copper = 8900 kg/sec Energy per second =…

Q: You are designing a new eco-friendly thermal coffee mug. It is shaped like a small globe to minimize…

Q: Q5B) A steel pipe of 170 mm inner diameter and 190 mm outer diameter with thermal conductivity 55…

Q: b) A plane wall is 205 mm thick and area 225 cm2 has a thermal conductivity of 14.86 W/m°C. The…

Q: Let's say a 3.0 gram copper wafer is dropped from a height of 50.0 meters. If 60% of the potential…

Q: Part A If the temperature of the room is 20°C and outside is 10°C, find the rate of heat flow for a…

Q: Q2: A person of skin temp. of 30 K and body surface area 1.75 cm, find: (a): net total power if he…

A: Given: The skin temperature, T = 30°C The area, A = 1.75 cm^2 The wall temperature, Tw = 22°C The…

Q: 1: In a steel sheet factory, plates in a rectangular shapes are made. One plate is maintained at a…

Q: Q2- Water flows inside a steel pipe with an ID of 2.5 cm. The wall thickness is 2 mm. and the…

Q: A house has a 120 square meter of net exterior wall area (after subtracting for windows, doors, and…

A: A house has a A=120 m2 of net exterior wall area (after subtracting for windows, doors, and so…

Q: The heat transfer across a 5” wall of firebrick is 500 W/m2. If the surface temperature on cold side…

A: Heat flux q = kA*dT/dx

Q: The heat transfer across a 5" wall of firebrick is 500 W/m2. If the surface temperature…

Q: Question 1: In your own words, write down the differences between thermodynamic and heat transfer.…

Q: Choose the right answer 1. The temperature profile for steady hest conduction through a plane wall…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: 2.33 One end of a 0.3-m-long steel rod is connected to a wall at 204°C. The other end is connected…

A: Data given- T1 = 204°C T2 = 93°C h = 17 W/m2 K Tair = 38°C L = 0.3 m D= 5 cm = 0.05 m

Q: Please solve both parts with handwriting please need with correct answer need awesome answer solve…

A: Since you have posted multiple questions, we will provide the solution only to the first question as…

Q: The heat flux applied to the walls of the biomass combustion furnace is 20 W/m2. The furnace walls…

A: Note:As per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: A tank contains water at 80 °C with a wall thickness 10mm. The thermal cinductivity of mild steel 45…

Q: 3.4 Estimate the rate of heat loss due to radiation from a covered pot of water at 95 ° C. How…

A: Introduction: Radiation heat transmission occurs in the form of electromagnetic waves, primarily in…

Q: 3 Brass cube "p = 8530 kg/m , c= side length = 9 mm, are annealed by heating them first to 813°C in…

A: Given that, Density of brass cube, ρ=8530 kg/m3Specific heat of brass, cp=380 J/kg,Thermal…

Q: a. The wall of a building has a surface area of 50 m2. The outside layer of the wall is 20 cm thick…

A: Given data: Surface area of the wall, A = 50 m2 Thickness of concrete wall, Lc = 20 cm Thermal…

Q: 1-3 A truncated cone 30 cm high is constructed of aluminum. The diameter at the top is 7.5 cm, and…

Q: temperature difference of 85°C is impressed across a fiberglass layer of 13 cm ickness. The thermal…

A: Temperature difference across a fibreglass, Thickness of the fibreglass, Thermal conductivity of…

Concept explainers

Conduction and Convection

When energy travels from one object to another it is said to have undergone heat transfer. Heat transfer is nothing but the transfer of thermal energy or internal energy from one thing to another, like e.g., when a vessel with water, kept on top of a burner, heats up because of the flame underneath it.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

1.10 A heat flux meter at the outer (cold) wall of a concrete building indicates that the heat loss through a wall of 10-cm thickness is . If a thermocouple at the inner surface of the wall indicates a temperature of 22°C while another at the outer surface shows 6°C, calculate the thermal conductivity of the concrete and compare your result with the value in Appendix 2, Table 11.
A plane wall 15 cm thick has a thermal conductivity given by the relation k=2.0+0.0005T[W/mK] where T is in kelvin. If one surface of this wall is maintained at 150C and the other at 50C, determine the rate of heat transfer per square meter. Sketch the temperature distribution through the wall.
The interior wall of a large, commercial walk-in type meat freezer is covered under normal operating conditions with a 2-cm thick layer of ice. One day, a power outage cuts electricity to the refrigeration system of the freezer. Estimate the time required to melt this layer of ice if it has a mass density of 700kg/m3 and a latent heat of fusion of 334 kJ/kg. Consider the air temperature inside the freezer to be 20C with a heat transfer coefficient of 2W/m2K for convection from the freezer surface to air, and clearly state the assumptions made in your calculations.
Using Table 1.4 as a guide, prepare a similar table showing the orders of magnitude of the thermal resistances of a unit area for convection between a surface and various fluids.
1.29 A spherical interplanetary probe with a 30-cm diameter contains electronic equipment that dissipates 100 W. If the probe surface has an emissivity of 0.8, what is its surface temperature in outer space? State your assumptions in the calculations.
Please solve both parts with handwriting please need with correct answer need awesome answer solve both handwriting i requested to u. Part6. An exposed 8 cm external diameter, 20 m long hot-water pipe at 80°C is losing heat to the surrounding (outdoor) air by natural convection. The average outdoor temperature is 5°C. The heat transfer coefficient is 25 W/m2°C. What is the heat loss by natural convection, in kW? A. 9.4 W B. 10.0 W C. 10.4 W D. 11.4 W Part7. A spherical ball with a diameter of 10 cm has an outer surface that is maintained at a temperature of 200°C. It is suspended in the middle of a room that has an average temperature of 20°C. If the surface emissivity is 0.8, determine the rate of radiative heat transfer from the ball to the room in W. (Choose the nearest value) A. 2.3 W B. 4.5 W C. 19.4 W D. 60.8 W
Question 1: In your own words, write down the differences between thermodynamic and heat transfer. (3 Marks) Question 2: Estimate the heat loss per square metre of surface through a brick wall 0.5 m thick when the inner surface is at 400 K and the outside surface is at 300 K. The thermal conductivity of the brick may be taken as 0.7 W/mK. (2 Marks) Question 3: A furnace is constructed with 0.20 m of firebrick, 0.10 m of insulating brick, and 0.20 m of building brick. The inside temperature is 1200 K and the outside temperature is 330 K. If the thermal conductivities are as shown in the figure below, estimate the heat loss per unit area. (5 Marks) 1200 K 330 K Fire brick X=0.20 m Insulating brick x=0.10 m Ordinary brick X=0.20 m k = 1.4 k = 0.21 k = 0.7 (WimK)
I need answer within 20 minutes please please with my best wishes
Consider a copper plate that has dimensions of 3 cm x 3 cm x 7 cm (length, width, and thickness, respectively). As shown in the following figure, the copper plate is exposed to a thermal energy source that puts out 126 J every second. The density of copper is 8,900 kg/m³. Assume there is no heat loss to the surrounding block. 126 J Copper Insulation Ⓡ What is the specific heat of copper (in J/(kg K))? J/(kg. K) What is the mass of the copper plate (in kg)? kg How much energy (in J) will be consumed during 11 seconds? J Determine the temperature rise (in K) in the plate after 11 seconds.
The thermal conductivities of wood is kwood = 0.1W/(m°C)and air is kair = 0.0234W/(m°C). Part A If the temperature of the room is 20°C and outside is 10°C, find the rate of heat flow for a wall of wood with area = 10 m² and thickness of 5cm. O 60 W O 304 W O 34 W O 200 W O 100 W Submit Request Answer Part B The wall of wood with thickness of 5cm is now replaced with two layers of wood and a gap of air between the wood. Each layer of wood has a 2.5cm thickness and the gap is 1cm. The rate of heat flow will, decreases. increases. stay the same. Submit Request Answer Part C The temperature in the air gap will be, O 20°C, between 10°C and 20°C, O 10°C,
2.33 One end of a 0.3-m-long steel rod is connected to a wall at 204°C. The other end is connected to a wall that is maintained at 93°C. Air is blown across the rod so that a heat transfer coefficient of 17 W/m2 K is maintained over the entire surface. If the diameter of the rod is 5 cm and the temperature of the air is 38°C, what is the net rate of heat loss to the air? 0.3 m- Wall Wall 204°C 93°C Steel rod 5-cm diameter Air 38°C Problem 2.33
Q2: A person of skin temp. of 30 K and body surface area 1.75 cm2, find: (a): net total power if he receives radioactive power from the surrounding walls 22 °C would be about 735 w. (6 = 5.7 x 10 12 w/cm) (b): The emissivity of surrounding walls. Good luck