You are building additional storage space in your garage. You decide to suspend a 10.0 kg sheet of plywood of dimensions 0.600 m wide by 2.25 m long from the ceiling. The plywood will be held in a horizontal orientation by four light vertical chains attached to the plywood at its corners and mounted to the ceiling. After you complete the job of suspending the plywood from the ceiling, you choose three cubic boxes to place on the shelf. Each box is 0.750 m on a side. Box 1 has a mass of 50.0 kg, Box 2 has a mass of 100 kg, and Box 3 has a mass of 125 kg. The mass of each box is uniformly distributed within the box and each box is centered on the front-to-back width of the shelf. Unbeknownst to you, one of the chains on the right-hand end of your shelf is defective and will break if subjected to a force of more than 700 N. There are six possible arrangements of the three boxes on the shelf, for example, from left to right, Box 1, Box 2, Box 3, and Box 1, Box 3, Box 2, and four more. Which arrangements are safe (that is, the defective chain will not break if the boxes are arranged in this way)? (Select all that apply.)

You are building additional storage space in your garage. You decide to suspend a 10.0 kg sheet of plywood of dimensions 0.600 m wide by 2.25 m long from the ceiling. The plywood will be held in a horizontal orientation by four light vertical chains attached to the plywood at its corners and mounted to the ceiling. After you complete the job of suspending the plywood from the ceiling, you choose three cubic boxes to place on the shelf. Each box is 0.750 m on a side. Box 1 has a mass of 50.0 kg, Box 2 has a mass of 100 kg, and Box 3 has a mass of 125 kg. The mass of each box is uniformly distributed within the box and each box is centered on the front-to-back width of the shelf. Unbeknownst to you, one of the chains on the right-hand end of your shelf is defective and will break if subjected to a force of more than 700 N. There are six possible arrangements of the three boxes on the shelf, for example, from left to right, Box 1, Box 2, Box 3, and Box 1, Box 3, Box 2, and four more. Which arrangements are safe (that is, the defective chain will not break if the boxes are arranged in this way)? (Select all that apply.)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 2) The figure shows a mechanical model of the Russel fracture traction device and the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The combined weight of the leg and the cast is W=210 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=6 cm. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=33°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) b) Find the tensile force T2 in cable 2. (Write your result in N) c) Find the angle α of cable 1 with the horizontal. Response
The figure on the left, below, shows a non-uniform bent rod with a mass of 5 kg. Your job is to determine the location of the center of gravity of this rod. You design an experiment: you connect a pin and cable to the rod such that it safely stays in static equilibrium under a force P that you apply. Then, you apply forces between 0-100 N, and measure the tension force on the cable using a cable tension meter. The results of your experiment are shown in the figure, on the right. Using this experiment, calculate (approximately) the horizontal distance (x in the figure) between point A and the center of gravity G of the bent rod. B C O I 20 cm 20 cm 60° D 50 cm Tension measurement [N] 60 50 40 30 20 -10 0 10 real data estimated fit 20 30 40 ܐܐܝ 50 P[N] 60 70 80 90 100
A rectangular rubber block is mounted into a multi-axial loading device capable of applying forces at each grip (blue) in the x and y directions. Forces applied at the grips are distributed over the entire contact area between the grip and the rubber block. The block is marked with a black diamond as shown in the unloaded state below: For each deformed state below, identify the load applied by each grip. The original position of the diamond is shown on each block.
Consider the two blocks on the seesaw below. The wedge is fixed at the center of the seesaw. If the larger box has twice the mass as the smaller, how could the seesaw be balanced? The distance measured from the center of the seesaw where the wedge is located is r. Note: For the larger box, r = rlarge and for the smaller box, r = rsmall
I need the answer as soon as possible please. Two weights are hung over two frictionless pulleys that are connected by a wire rope to a 500 lb horizontal block that are in between and below them. The wire rope attached to the upper left end of the block and to the left pulley is at 45 degrees with the horizontal and the wire rope that connects the upper right end of the block to the right pulley is at 30 degrees with the horizontal. If the weight on the left pulley is 50 lb, fs = 0.30 and fk= 0.20 on the surface of block what weight W on the right pulley will cause the 500 lb block to just start moving to the right?
A car is hanging over a hole, supported by a rope tied to the ceiling and a person pulling the rope. How much force is exerted by the person in the configuration below, given the car weighs 3500 lbs? ** å 30° 则
In the figure below, the masses of each object are: m₁ = 2.00 kg, m₂ = 2.00 kg, m³ = 3.00 kg. The labeled distances are: d₁ = 30.0 cm, d₂ = 106 cm, d3 = 60.0 cm (where d is the x distance for the center of the block). The height of each block is h₁ = 21.0, h₂ = 28.0 cm, and the h3 = 11.0 cm. Assume the center of mass for each individual object is at the center of the object. Hint: Consider the final center of mass (x,y) relative to the axes shown in the figure. Note the positions of the boxes relative to the axes and to one another. Determine the positions, x and y, of the center of mass for the system below. y Enter to 3 significant figures Center of mass (x, y): ( d1 m1 d3 d2 h1 cm m3 m2 h2 11h³ X ✔cm) Think and Prepare 1. For each of the boxes, m₁, m₂ and m3, where is the center of mass located? Carfefully, identify the
Q3: The diagram shows the open bonnet of a car. The bonnet is vertical force V held open at an angle of 60° to the horizontal by a vertical force V applied at one end of the bonnet (shown on the diagram). The car bonnet bonnet is 0.90 m long, has a weight of 25 N and its center of gravity G is 0.35 m from the hinge at O. 0.90m 1) On the diagram, draw and label the two forces other than V acting on the bonnet. 2) By taking moments about O, show that the vertical force V applied at the end of the bonnet is 9.7 N. 60 horizontal hinge O 3) Calculate the magnitude of the force acting at the hinge O.
Two weights are hung over two frictionless pulleys that are connected by a wire rope to a 500 Ib horizontal block that are in between and below them. The wire rope attached to the upper left end of the block and to the left pulley is at 45 degrees with the horizontal and the wire rope that connects the upper right end of the block to the right pulley is at 30 degrees with the horizontal. If the weight on the left pulley is 50 lb, fs= 0.30 and fk = 0.20 on the surface of block what weight W on the right pulley will cause the 500 lb block to just start moving to the right? *
1. A uniform stick can be balanced on a knife edge 10 cm from one end when a load of 200 N is hung from that end. When the knife edge is moved 5 cm further from the end, the 200 N load has to be moved to a point 8.75 cm from the knife edge to obtain a balance. Find the length of the stick and its weight.
asap
The figure shows the cross section of three cylinders, 1m long, given the density of steel 500 lbs/cu.ft. Find the reactions between all of the cylinders and the ground in lbs. Units are in feet.