Yo- Vo усх) — Vс) - Bump h(x)

Q: For more than a century, woodsmen harvested trees inSkowhegan, ME, elevation 171 ft, and fl oated…

A: Given data: Length of the channel , L = 72 miles = 380160 ft Skowhegan elevation, z1 = 171 ft…

Q: A tank of water 1 m deep, 3 m long, and 4 m wide into the paper has a closed sluice gate on the…

A: Water tank dimensions:Depth (h) = 1 mLength (b) = 3 mWidth into paper (w) = 4 mInitial depth at t =…

Q: For the water channel fl ow of Fig.=, h 1 = 0.45 ft,H = 2.2 ft, and V 1 = 16 ft/s. Neglecting losses…

A: Write the given data.

Q: Assuming that the pressure is uniform on each of the ch the pressure difference between the upper…

A: GivenF=-1950 N  since -y directionV=55 m/sh=6mmw=215mml=120mm

Q: The Kishwaukee river has a volume flow rate of 21 ft3/sec with a depth of 2.8 ft. If the…

A:

Q: In Fig.  let V0 = 1 m/s and y0 = 1 m. If the maximumbump height is 15 cm, estimate (a) the Froude…

A: Given data: The bump height, Δh = 15 cm. The approach velocity is, V0 = 1 m/s. The approach water…

Q: A 4-ft-diameter finished-concrete sewer pipe is half full ofwater. (a) In the spirit of Fig.…

A: Given data: The diameter of pipe, d = 4 ft. Calculate the area of the half-full channel, by using…

Q: Q2) A flocculation basin has dimensions of 17.4m length, 11.4m width , and 5.8m depth, with three…

A: Given Data17.4mw=11.4md=5.8mμ=1.139×10-3N.s/m2ρ=999.1kg/m3CD=1.8 ***As per our company policy we are…

Q: For the water channel flow of Fig. , h 1 = 1.5 m,H = 4 m, and V 1 = 3 m/s. Neglecting losses and…

A: Given data: Depth of the upstream, h1 = 1.5 m. Height of the channel, H = 4 m. The upstream…

Q: A vertical sluice gate spans the full width of a rectangular channel 6.0 m wide. If the downstream…

A: The hydrostatic forces on both sides of the sluice gate act at the CG of the body. The resultant…

Q: A large tank is continuously filled with water to a depth of 15 m. A 0.1 m diameter hole is located…

A: Given, Diameter of hole         = 0.1m Height of the tank       = 15m Hole is located above 8m from…

Q: How long will it take for all the water to drain from the tank?

A: Given equationthe hole area at the bottom of the tank, a=0.05 m2acceleration due to gravity, g=9.8…

Q: Water flows in a channel with uniform curvature ?. The channel has height ℎ = 5 mm and width ? = 190…

A: GivenF=-2000 N  since -y directionV=53 m/sh=5mmw=190mml=100mm

Q: Water at 20°C flows through the orifice in Fig. ,which is monitored by a mercury manometer. If d = 3…

A: Given Data Area of the pipe, A=πD24=π0.0524 Rate of the discharge, Q=20m3/h  To find out the…

Metrology of surface finish

In general terms, the application of scientific principles in the study of measurements is known as metrology. When speaking about measurement, it could be of time, length, microstructures, grain structures, internal crystal discontinuities, surface roughness, measurements of angles, height, width, and so on. While coming to the domain of mechanical engineering, metrology is considered the science of measurements of surface finish, length, surface texture, and angles.