yearQ3/Complete the earthwork calculation sheet and plot the resulting massdiagram. Assuming Shrinkage-10%(20 Marks)Length alongroad100 mEnd areacut (m²)End areafill (m²)Volume ofcut (m²)Volume offill (m³)Adj. fillMassdiagram(m³)ordinate(四)0002400430006008010010030012020014001620001800020200

Plotting the Mass DiagramTo plot the mass diagram:1. Use the stations as the x-axis.2. Use the…

Answered: year Q3/Complete the earthwork…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

TRUE or FALSE When calculating the Group Index for soils that belong to groups A-2-6 and A-2-7, use the partial Group Index for Liquid Limit. Please answer this asap. For upvote. Thank you very much
1. Using the design chart below. Estimate the SN if W18=10x10^6, R=90%, So=0.35, Mr- 10000Psi, ΔPSI=3. Use the chart below. TL Overall standard deviation, S. TL Design serviceability loss, APSI 50 10 5.0 99.9 0.2 99 1.0 0.4 0.6 90 0.5 0.5 0.1 1.5 0.05 2.0 80 70 60 50 2.5 3.0 9 87 6|5 4 3 1 Eхample: 6.5 5.5 4.5 3.5 2.5 1.5 W18 = 5 x 106 Design structural number, SN R = 95% S, = 0.35 MR = 5000 Ib/in? APSI = 1.9 Solution: SN = 5.0 Figure 4.5 Design chart for flexible pavements based on the use of mean values for each input.
Construction Surveying
What is meant by Proctor’s Compaction test. Main purpose of learning Proctor’s Compaction Test?
The results of a CPT test performed for a commercial site are presented in the image (You already classified the soil layer in homework #2). The layer soil type is shown by the legend and corresponding numbers in the figure. A strip footing with a size of 3x30 is built on the surface of the mentioned strata. A 300 kN/m load is acting on the footing. Use Schmertmann's method to compute the settlement of this footing 1 year after construction and 30 years after construction. Please show your calculation for at least one layer if you want use excel software for this problem. For easier calculation use E₂ = 39c- • • Neglect the foundation weight. • Assume the layers are in dry condition. Use unit weight as table below. Layer No. 1 2 3 4 5 6 7 Unit weght kN/m3 17 17 19 18 18.5 18 18
The following data are cross-section notes of the ground which will be excavated for a roadway having a base width of ten meters: Station 122 10+ Station 179 10+ 3.0 2.1 2 2.6 2.75 3.4 6.1 0 5.3 6.5 7.1 Determine the volume of excavation by end-area method (in m³)
Please round to the nearest One (i.e., 1). PLEASE DO NOT USE COMMA(S) ON YOUR ANSWER!!! A proposed embankment fill requires 6900 ft³ of compacted soil. The void ratio of the compacted fill is specified as 0.5. Four borrow pits are available as below, which list the respective void ratios of the soil and the cost per cubic feet for moving the soil to the proposed construction site. Make the necessary calculations to determine the total cost for each pit. Assume the specific gravity of soil solids, Gs to be the same at all pits. 1. Calculate the volume of solid (Vs) = ft³ Borrow Pit A: void ratio= 0.91 and the unit cost = $9 /ft³ 2. Calculate the total cost to pay to Pit A = Borrow Pit B: void ratio = 0.95 and the unit cost = $ 11 /ft³ 3. Calculate the total cost to pay to Pit B = Borrow Pit C: void ratio = 1.05 and the unit cost = $8 /ft³ 4. Calculate the total cost to pay to Pit C = Borrow Pit D: void ratio = 0.65 and the unit cost = $ 10/ft³ 5. Calculate the total cost to pay to Pit…
There are three commonly used methods to calculate the point bearine capacity of pilfoundations in sand What are they? Which one considers soil deformable?
5 3 7 8 Table below shows the chainage (length), cut and fill end areas Earthwork Calculations Station 0+30 1+00 1+50 cut end area fill end area (sf) (sf) 320 650 270 780 300 620 cut volume fill volume (cy) (cy) total volume total volume of fill of cut For the earth calculations shown on the left, compute the total volume of fill. (sf = square feet, cy= cubic yards, 1 cy= 27 cubic ft) Hint: When the end areas of cut or fill have been computed for adjacent stations, the volume of cut or fill between those stations can be computed by simply averaging the end areas and multiplying the average end area by the distance between the end area stations. Length is the difference between stations. V-(A1+A2)/2*L 60,800 cy 53,000 cy 2.252 cy 2,021 cy
Indicate the general advantages and disadvantages associated with hydraulic fill placement methods.
- Once answered correctly will UPVOTE!!

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS