x/-30° A O a. 6.41 + j9.70 A O b. 6.41 + j42.21 A O c. 42.43 + j9.70 A I₁ O D. 20.66 + j25.30 A O to. 74.31 + j21.23 A O f. 26.82 + j22.37 A O g. 0.49 +j12.55 A O h. 13.00+ j46.80 A 222 www Vo j4Ω m I2 3Vo + O 13 Question 2) Since the amplitude of the current source in the circuit above is x= 13, find the value of the ambient current 12. Question 2) In the above circuit amplitude of the current source is x= 13, then find the 12 mesh current. -j2 92

Q: What advantages do integrated circuits have over discrete ones?

A:

Q: Q/1/A single-phase, half-wave, controlled has a source 220V at 50 HZ and is feeding a load R-2002…

A: To solve this problem, we need to use the following equations: Average load voltage = Vmπ × (1 +…

Q: Design a synchronous counter using JK flip-flops to produce the following sequences. 3 5 1

A: According to the question, we need to design a synchronous counter, which follows the following…

Q: Draw 1.5 cycles of the analog signal and show the location and the value of each sample. [Q1] A…

A: Given a sinusoidal signal having, Frequency, f = 800 Hz                   T=1f=1800 Hz=1.25 ms…

Q: write note on ring modulator

A: Ring Modulator:

Q: Create an RC circuit. Calculate and measure the time constant. Measure the discharge time at least 5…

A: RC Circuit A resistor-capacitor circuit, often known as an RC circuit, is a type of electrical…

Q: Q) A CRO can be used to measure--- O A.C voltage. O D.C voltage. O Frequency. O All of above.

A: CRO displays the waveform on its screen.

Q: What is the cross over distortion in class B?

A: In the given questions we need to discuss about the cross over distortion in class B amplifier.

Q: Ex. 295. Refer to Figure 295 Determine: 2%Settle Time, Peak Time, Rise Time, Percent Overshoot,…

A: Settling time : The time it takes for the output to reach and stay within a specific error band…

Q: Draw What is the cross over distortion in class B?

A:

Q: Ic IB Ig NO SIGNAL V BB Vcc= 12.5 V Rc= 2.5 k2

A: we need to draw D.C. load line.

Q: Propose an electronic circuit which has an input/output waveform like the one shown in the figure…

A: The above question is based on operational-amplifier based circuit design.The input voltage VIN is a…

Q: Construct an Multiplexer 8*1 with two Multiplexer 4*1 and additional gate

A:

Q: Q8. What is the difference between Zener breakdown and Avalanche breakdown?

A: The main difference between Zener breakdown and avalanche breakdown?

Q: QUESTION-4 aN-Pleas Please answer the following: a)awiwn) What are the causes of impulse voltages?…

A:

Q: What happens to cut-in voltage when the temperature increases? a) Cut-in voltage increases b) Cut-in…

A: Option :b ( correct answer)

Q: Impulse flashover test is conducted to know the characteristics of insulators and lightning…

A: The power system has to transmit power from the generation side to the load side. For this purpose,…

Q: Q4 Compare between Vametcan and Vazractca Vure = Vaameoretica V12 tractca)

A: Resistors, inductors and capacitors form an integral part of any electrical circuit. A source,…

Q: What are Test comparators?

A: We have been asked about Test comparators.

Q: about nyquist stability criterion in deatials

A: Need to find about nyquist stability criteria

Q: Q5/ What is static VAR Compensator? Draw its schematic diagram. What are the two tasks of Thyristor…

A:

Q: xplain the following: a) Elaborate why the method of inverted R-2R ladder is preferred in DAC as…

A: A) The method of inverted R-2R ladder is preferred in DAC because: Easier to build precisely as…

Q: Explain voltage and frequency operating limits

A: To move a charge from position to another position in an electric field a force, this force is…

Q: Please write short introduction about AC Circuits - Series Circuits

A: An a.c circuit differs from a d.c circuit in many respects. First, in a d.c circuit we consider…

Q: Show me step by step how to do this design

A: The implementation of the logic gate using the IC in multisim software needs to be briefed.

Q: Explain the operation of Negative clipping with circuit diagram and waveforms.

A:

Q: For a DC-DC Converter; The input voltage of the circuit is 12 V, the switching frequency is 1 KHz,…

A: A DC-DC converter has, Input voltage (Vin)= 12 volts Output voltage (Vo)= 48 volts Output Power…

Q: Explain the PWM control and duty cycle generation in phase-control of SCR

A:

Q: Please validate the saturation assumption

A:

Q: 01) For the Oscillation circuit shown in Figure (1), derive an expression for the frequency of…

A: Oscillator Oscillator is a electronic or mechanical device, its based on working of oscillation. we…

Q: Do you think that the design procedure is easy using multiplexer?

A: Multiplexer: The multiplexer is a common sensetool that switches one in allseveraenterstrains to a…

Q: what is oscillating column and smoothening column in cascade voltage multiplier circuit ?

A: What is cascade voltage multiplier circuit ? The cascade circuit is a unique type of rectifier that…

Q: Q#3 : How transient stability limit can be increased?

A: Methods to improve transient stability : Using high speed circuit breaker :       It increase the…

Q: Explain dual slope ADC and successive approximation ADC with neat block diagram and compare the two…

A: The dual-slope ADC mainly consists of 5 blocks: Integrator, Comparator, Clock signal generator,…

Single Phase Induction Motor

The single-phase induction motor or engine consists of a single rotating phase in the stator and a rotating cage in the rotor. When phase one supply is connected to the stator winding, a magnetic field is generated. In the pulsating field, the rotor does not rotate due to inertia. So, a single-phase import motor does not start and requires some initial methods.