WWW

Q: What is Non-Dot Standard Specification?

A: Specification of Non-Dot Standard:

Q: How are GIS hardware differ

A: The tangible devices and instruments needed to execute and display software results are referred to…

Q: I'd appreciate it if you could elaborate on what you mean by "GIS," thanks.

A: GIS stands for Geographic Information system and are computer-based tools that investigate…

Q: Define Eccentricity,

A: Eccentricity is a term is used in the loading condition of the engineering. for example, the load on…

Q: I would appreciate it if you could explain what you mean when you say "GIS."

A:

Q: Give the table mentioning AQI Values, Descriptors and Colors used?

A: The Air quality Index is often abbreviated as AQI. The government has prescribed some set of values…

Q: Define the Design working life ?

A: Design Life The design life (or design administration life) of a structure, other construction or…

Q: In detail what is the CSI MasterFormat and what is listed in division 28?

A: Answer  CSI MasterFormat also known as "Dewey Decimal system" is the product of the Construction…

Q: What do you mean by the slice action and how many slice operated dimensions are used?

A: #1What do you meant by the slice action?? A slice operation is defined as the particular filtration…

Q: "Repository, modelling tool, documentation instrument, engineering instrument, and construction…

A: 1. Repository A repository is a central location where data, information, or software code can be…

Q: Who keeps the design or site information in their possession?

A: The life cycle of the project can be defined as a mechanism by which a project is carried out from…

Q: create (P,L,E,A,N,U,G) 2D drawing using lines, circles, curves,etc

A: Here is your drawing

Q: Define scale factor?

A: The size by which the shape is reduced is called as its scale factor. It is used when we need to…

Q: what was the unit used in the plan shown above ? autocad

A: There base unit in AutoCad is inch.

Q: What is (-3,0) scale to 1/3

A: Given: coordinates (-3,0) scale = 1/3 To find convert the coordinates to the given scale.

Q: actors that cause hardness along with a bibliography

A: The water hardness may be simply defined as the amount of dissolved calcium and magnesium in the…

Q: Define “building element.”

A: Building element:

Q: * To draw an arc angle between two intersecting lines Fillet O Block O Trim Chamfer O If we want to…

A:

Q: What are the steps involved in the construction of a control unit that employs vertical coding, and…

A: It has been asked in the question to determine the steps involved in the construction of a control…

Q: Define Minimum Dimensions

A: Brief concept introduction- Minimum Dimensions- Minimum Dimension is a very wide term and it…

Q: Describe what is Translational slides.

A: Translational slides:

Q: Explain the Eurocode terminology :UPL

A: The Eurocode terminology :UPL

Q: For the given structures, determine the degree of indeterminacy. 1. ♫

A: This question is related to the Structure analysis

Q: What is the difference between primary standards  and secondary standards in AAQS?

A: Primary standards:These standards for the air pollution control considered the public health…

Q: Determine the number of linear feet needed for the shoe and double top plates for the building plans…

A: For plan 1   Total area of wall = (53 x 30) = 1590 ft2  For one shack and double top plates…

Q: The coordinates of centroid for the following section is 150 mm - 20 mm 20 mm 20 mm 300 mm 500 mm

A:

Q: Discuss how volume studies are being conducted

A: Traffic volume studies are conducted to determine the effectiveness of traffic control…

Q: Write a few lines on RFI?

A: Request for information is a process of business in which the main motto is  to collect the…

Q: What is used to mark the tape lengths?

A: In surveying, tapes are used to measure distances that are level, vertical, or sloping. Tapes are…

Q: WHICH ACI CODES DID YOU USE?

A: A building layout is given, we need to find out which ACI code is used in solving the problem

Q: What is the USGBC Web?

A: The United States Green Building Council is the organization which supports and promotes…

Q: Define Class 1 and 2 of cross sections

A: Class 1 cross-sections are those which can form a plastic hinge with the rotation capacity required…

Q: Define the terms Streamlines, Streaklines, Stream tube?

A: Streamlines Streamlines are a family of curves that are outright tangent to the velocity vector of…

Q: Write the definition of standard specification?

A:

Q: cale is considered a mall scale one of the answers ge scale ddle scale

A: 1/25000 scale is considered as  A) small scale  B) none of these  C) large scale  D) middle scale

Q: Define Torsion,

A: Torsion: The twisting of a material by the loading of external forces i.e couple which produces…

Q: What are the possible Geometric Design? Make a table Containing the Geometric Design and Design…

A: Geometric design is the process of determining the layout and dimensions of visible features of a…

Team Management

To complete a specific task or to accomplish organizational goals along with increasing work productivity, individuals need to come together and think along a common path and direction. There are certain tasks in an organization that cannot be done alone and the involvement of more individuals is essential. These groups of individuals who work together for a common goal compose a team and the individual members involved are known as team members.