Write the code needed to perform the following operation and insert it as needed in the program shell below. Setup Port A, pin 4 as input, with pull up resistor enabled, Setup Port H, all pins as an outputs, Continuously read the input on Port A, pin 4 Write to Port H, all pins (all 0s or 1s) the data read from Port A, pin 4 (0 or 1) Write the code so as to not affect any other port bits or setup   INCLUDE     .DEF TEMP=R16 .CSEG ; The start of the code segment .ORG 0X0000 ; Set the beginning of code at the reset interrupt vector RJMP MAIN ;jump to main program from the reset interrupt   MAIN: LDI TEMP, LOW(RAMEND)    ; Setup Stack OUT SPL, TEMP        ; Set SPL to the low byte of RAMEND LDI TEMP, HIGH(RAMEND)   ; OUT SPH, TEMP        ; Set SPH to the high byte of RAMEND ;insert code here                             LOOP: ; A continuous loop is an essential ; part of any embedded program ;insert code here                     RJMP LOOP    ; Start the LOOP over

Q: The assignment is to create a MIPS program that does an integer multiply using adds and shifts. The…

A: MIPS stands for "Million Instructions Per Second" and is a measure of the number of instructions…

Q: Write a python program to accept two numbers and perform the following operations based on the…

A: Please find the answer below :

Q: Which registers are used to store function parameters? O PC, IR, and $sp O $ra and $at O $a0, $a1,…

A: registers  $a0,$a1,$a2,$a3 are used to store function parameters or argument

Q: Help with program that will fork to a child process and prompts the user for two input numbers. Then…

A: Given, First start by asking the user for two floating point values, following steps: The program…

Q: 4. Write MIPS code for the following: Add two integer numbers and display the results on the screen.

A:

Q: In C or C++ You need to build a signal handler which catches a signal to abnormally abort a…

A: Start the program.Register the signal handler function mySignalHandler for the SIGINT signal using…

Q: What is the output of the following Pep/9 code, if the input is 5, 9, 6, -12, 7, 14. Properly…

A: BR       main  number:  .EQUATE 6                      ;constant j:              .EQUATE 4…

Q: • Write the Verilog code and testbench for the following circuit D o C t2 AB

A: Given : Different values of A,B,C,D Output : Value of Y at different values of A,B,C,D.

Q: -1 x using the power series Write a program that computes the value of tan x° expansion x - + ... 5…

A: % power series expansion clear clc   % compute value of pi pi =…

Q: Keep in mind that the operation code is not the same thing as the operands.

A: Given:  Each conference language sentence is separated into op code and operator according to your…

Q: AIM- To find  the true reading of the temperature in degree Celsius.    STATEMENT- In a…

A: ALGORITHM OF PROGRAM-   Convert 57 from decimal form to hexadecimal form (39H). Move 39H to…

Q: Program a circuit where a yellow LED light will turn on when a button is pressed and remain on for 4…

A: Program: turn on a LED when the button is pressedturn it off when the button is not pressed (or…

Q: and you made a mistake the final states are q1 and q2

A: Unambiguous grammar: A grammar can be unambiguous if the grammar does not contain ambiguity that…

Q: What are PUSH statements are normally used for?

A: In MLPS or the Multiprotocol label switching can be explained as the technology which helps in data…

Q: Answer the following questions regarding execution of loops. Assume that the code below is executed…

A: 0x0001 = 1 in decimal 0x1000 = 255 in decimal kk=1 mm=255