k = 2 lb/ft0BTwo blocks A and B have a weight of 11 lb and 6 lb,respectively. They are resting on the incline for which thecoefficients of static friction are μA = 0.16 and µB = 0.23.Determine the angle 0 which will cause motion of one ofthe blocks. What is the friction force under each of theblocks when this occurs? The spring has a stiffness of k = 2lb/ft and is originally unstretched. Determine the smallestangle which will cause motion of one of the blocks.Determine is the friction force under the block A at thisangle. Determine is the friction force under the block Batthis angle.

Given : Weight of block A = 11 lb weight of block B = 6 lb Coefficient of static friction for A =…

Answered: wo blocks A and B have a weight of 11…

wo blocks A and B have a weight of 11 lb and 6 lb, espectively. They are resting on the incline for which the pefficients of static friction are µA = 0.16 and µB = 0.23.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Using the Stiffness method (FEA) determine the veritical displacement at the point load. Assume all areas have an AE value of 1.0 A 3m C 4m 10kN B
A roadway sign weighs 7.2 kN and is supported by a structural pipe that has an outside diameter of 250 mm and a wall thickness of 11 mm. The resultant force of the wind pressure acting on the sign is 9 kN, as shown. Assume a = 8.2 m, b = 3 m, Pz = 9 kN, and %3D Py = 7.2 kN. (a) Determine the normal and shear stresses oH, TxyH at point H. (b) Determine the normal and shear stresses OK, TyzK at point K. a H K Answers: OH = i MPа. TxyH 28.6 MPa. OK i MPа. TyzK i ! MPa. II
Situation 1| An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets. The property of the channel is given below: Depth, D = 225 mm Flange Thickness, t, = 9mm Flange Width, B; =112.5 mm Web Thickness, tw=9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t= 100 MPa on shear, for bearing, o,=200 MPa on single shear, o,-260MPA on double shear. 1. Determine the location of centroid, y, from top of the beam in mm. 2. Determine the moment of inertia, I, of the section in mm“. 3. Determine the maximum allowable moment, Mall, in kn-m, base on the beam's cross-section.
Find the lightest S-shape for the beam shown if the working stress in bending is 175 MPa. What is the maximum bending stress in the beam selected? Show the complete solution and correct answer without shortcut, with FBD. THank you
A column is made of steel and concrete, if the normal forces on steel and concrete are 6.8kip and 145kip and the allowable stresses of steel and concrete are 36ksi and 5.5ksi, and the cross sectional areas of steel and concrete are 0.3068in^2 and 45.5456in^2, determine whether the still or concrete will fail when given a yield factor of safete of 1.69
O The slab shown below is loaded with D = 8 kN/m² and L= 4 kN/m. All beams are 300 mm in width and 600 mm in depth and all columns are square with side length of 300 mm. If the slab is 200 mm thick and is reinforced with 10 mm diameter bars in both directions, then: (a)Calculate the design moment of the slab at A. (b)Calculate the uniformly distributed load on beam B1. 8.75 m II 5.6 5.6m IV III B1 7.0 m 5.6 m
BRAIN EXERCISE PROBLEM 1 Determine the maximum shear stress and the maximum flexural stress of the beam. The cross-section of the beam is 150 mm x 350 mm. A B 10 KN 15 KN/m C 1.50 1.00 1.50 10 KN/m D D.Lopez 2.00 in meters Figure A: Overhanging Beam E
I want an urgent solution with proper explaination.
Two blocks A and B have a weight of 10 lb and 6 lb, respectively. They are resting on the incline for which the coefficients of static friction are 0.15 and 0.25 respectively . Determine the incline angle ϴ for which both blocks begin to slide. Also find the required stretch or compression in the connecting spring for this to occur. The spring has a stiffness of k = 2 lb/ft. Pls show full solution with FBD.
Please correct answer
.: Find the deflection of the simply supported beam of 12 m span, and then compare with ACI Code limit. The beam width (500 mm) and high (800 mm). f 'e = 21 MPa, live load= 8 k/m², surfacing load=1.0 kN/m²). Solution:- Beam weight=0.5(0.8) (24)= 9.6 kN/m WD 9.6+(1.0) (0.5)= 10.1 kN/m WL-8 (0.5) = 4 kN/m 5 Ws.14 5 384 Eclg (10.1+4). (12000)* 384 4700 √21 (500) (800)³/12 (Table 6.2) ACI Code limit A 1 360 12000 360 8.3 mm check A limit = 33.3 mm > 8.3 mm (O.K.) 1 360
The design specifications of a 1.2-m-long solid circular transmission shaft require that the angle of twist of the shaft not exceed 4° when a torque of 750 N-m is applied. Determine the required diameter of the shaft, knowing that the shaft is made of a steel with an allowable shearing stress of 90 MPa and a modulus of rigidity of 77.2 GPa. The required diameter of the shaft is mm.