The design specifications of a 1.2-m-long solid circular transmission shaft require that the angle of twist of the shaft not exceed 4° when a torque of 750 N-m is applied. Determine the required diameter of the shaft, knowing that the shaft is made of a steel with an allowable shearing stress of 90 MPa and a modulus of rigidity of 77.2 GPa. The required diameter of the shaft is mm.

The design specifications of a 1.2-m-long solid circular transmission shaft require that the angle of twist of the shaft not exceed 4° when a torque of 750 N-m is applied. Determine the required diameter of the shaft, knowing that the shaft is made of a steel with an allowable shearing stress of 90 MPa and a modulus of rigidity of 77.2 GPa. The required diameter of the shaft is mm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If the normal stress in each rod must be limited to 280 MPa, determine the minimum diameter d₂ required for rod (2). 80 KN d₁ O 18.2 mm O 28.7 mm O 24.6 mm O 30.2 mm O 21.7 mm 140 KN 140 KN B (2)
o
1. A steel circular bar (the yield stress oy = 350 MPa) with diameter d = 60mm is acted upon by combined moments M and axial compressive loads P at its ends. Taking P = 500 kN, determine, based on the Von Mises criterion of yield failure, the largest allowable value of M. d M M P- P.
A hollow steel [G = 12,000 ksi] shaft with an outside diameter of 3.50 in. will be subjected to a pure torque of T = 4420 lb-ft. Determine the maximum inside diameter d that can be used if the shear stress must not exceed 8,000 psi and the angle of twist must not exceed 3° in an 8-ft length of shaft. O 3.07 in. O 2.38 in. O 2.75 in. O 2.52 in. O 1.50 in.
If the 2-in.-diameter shaft is made from cast iron having tensile and compressive ultimate stress of 1sult2t = 50 ksi and 1sult2c = 75 ksi, respectively, determine if the shaft fails according to Mohr’s failure criterion.
A hollow steel shaft with an outside diameter of 75 mm and a wall thickness of 5 mm is subjected to a pure torque of T = 3650 N-m. The shear modulus of the steel is G = 80 GPa. Determine the magnitude of the angle of twist in a 2.0-m length of shaft.
Problem 1: Obtain a preliminary design of the shaft by performing the following tasks. Note that forces T=2880 N and T;=432 N. The maximum bending moment is atx= 230 mm (point B), and it equals M= 698.3 N•m completely reversed, where the torque is constant at 612 N.m at the same point. The shaft material is AISI 1020 CD steel. Take the stress concentration conditions at B to be Shoulder fillet-sharp, with notch radius r=0.6 mm (Table 7-1). y 230 mm T, 280 mm 30-mm dia. T C 300 mm 250-mm dia. 400-mm dia. 270 N 1800 N a) Sketch a general shaft layout in 2D (x – y axes), including all components and torques, then calculate all reactions. b) Based on the current shaft dimensions and using only forces at B and C, find the lowest critical speed of the shaft. c) Discard the indicated shaft diameter and use DE-Goodman criteria to determine the critical diameter of the shaft based on infinite fatigue life with a design factor n of 1.5. (Take the same value of endurance limit as that used in…
D) If the diameter of the cross-section of the beam is 500 mm compute for the maxumum shearing stress E) ss
Avoid truncation in the middle of solution (3 decimals for final answer )
Please solve it correctly with free body diagram.
Subject: