dimensiconscan with followingAngle of Ascent =150 degree, Angle ofDwell_-4o",Angle of Descent= 60 deprce, Duell of restAtheCycle, Maximum follower lift= 30mm,Follower Ty pe= Knife edge follower.The Rise of follaver is SHM anod fall of.Q Design athe follawer is with uniform velocity

Answered: Image /qna-images/answer/e2dc6185-0c42-49d3-8156-a42003f56cf3.jpg

with following dimensicons Qt+ Design a Angle of Ascent =15o degree, Angle of Dwell-4o", Angle of Descent= 60.dgrce, Duell of restofthe Cycle, Maximum follomer lift = 30mm, Follower Ty pe= Knife edge follower. The Rise of folower is SHM and Fall of the follawer is with uniform velocity Cam

with following dimensicons Qt+ Design a Angle of Ascent =15o degree, Angle of Dwell-4o", Angle of Descent= 60.dgrce, Duell of restofthe Cycle, Maximum follomer lift = 30mm, Follower Ty pe= Knife edge follower. The Rise of folower is SHM and Fall of the follawer is with uniform velocity Cam

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Assignment no 2 dimensieons. Qt4 Design a Angle of Ascent =15o degree, Angle ofDuel_4o", Angle of Descent= 60 dgnce, Duell of restAthe Cycle, Maximum follower lift= 30mm, Follower ty pea knife edge follower. The Rise of follwer the follower can with following dimensions. %3D is SHM and fall of is with uniform velocity
Design a helical extension spring to hold the roller follower against the cam as shown in Figure 1. The maximum extension of spring (ymax = 8.3 mm), the dynamic load varies from 250 N at the low position and 400 N at the high position . The diameter of the circular cam is 200 mm rotates off center with an eccentricity of 25 mm and operates the roller follower that is carried by the arm. The speed of the cam is 200 rpm. Design choices, (C= 10 ), shear modulus G= 80 GPa , A227 as a material for the spring, Wire endurance limit Sew = 310 MPa, factor of safety for spring body is 1.5. The spring ends are standard. a. Check the initial tension in the spring and compart it with minimum load. b. Determine the physical parameters of the spring. c. Check the surging of spring. 200 mm -100 mm- - - Spring 25 mm ww
Draw the displacement diagram and profile of the cam operating a roller reciprocating follower and with the following data: Shaft diameter 10 mm; Minimum radius of cam 25mm; lift = 40mm; roller diameter=15mm. The cam lifts the follower for 120° with Simple Harmonic Motion (SHM) followed by a Dwell of 30° .Then follower lowers down during 150° of cam rotation with SHM followed by a Dwell period. If the cam rotates at a uniform speed of 100 RPM clockwise direction. Calculate the maximum velocity and acceleration during the ascent and descent period. Maximum Velocity and Acceleration During Ascent and Descent
An offset type of follower in which the motion follower is along an axis from the axis of the cam center.
Assignment no cam with following dimensions. Angle of Ascent =150 degree, Angle ofDuel_4o", Angle of Descent= 60 donmce, Duell of restAthe Cycle, Maximum follower lift= 30mm, Follower ty pea knife edge follower. The Rise of follaver is SHM and Fall of the follower is with uniform Qtz Deign a y. Q2+ Explain yeloidal Motion,
An engine of 175 mm bore and 375 mm stroke is governed by hit and miss type governor to 220 rpm. With a fixed setting of the gas supply and ignition advance, indicator diagrams gave the following values of mean effective pressure. Firing, positive loop 5.7 bar, negative loop 0.25 bar; missing negative loop 0.42 bar. When developing 6 kW the explosions were 100 per minute and the gas used was 0.1 m per minute. Calculate the friction power and assuming uniform gas supply per explosion, find the gas consumption per minute at no load.
Q5:- A symmetrical cam with circular flank operates a flat-footed follower. The lift is 8 mm, base circle radius is 25 mm and the nose circle radius is 12 mm. If the total angle of cam action is 120°, find the maximum acceleration when the cam shaft rotates at 500 rpm.
In a cylindrical type of cam in which the follower reciprocates or -------- in a direction parallel to the cam axis
Design a variable stroke quick return mechanism with stroke ranges from 80mm to 220mm,fixed link is 110mm and time ratio is 2.
What is the purpose of verifying a toolpath on the screen of a CAM system before producing the program code for it?
I need answer please
B3