Wind blows on the side of the fully enclosed warehouse building as shown which is located on open flat  terrain in Bacoor City, Cavite. If the building is classified as Category 5 and under Exposure C with a wind  speed of 230 kph, determine the design wind pressures on all sides of the building and on the roof of  the building. Use NSCP 2015.

Q: A flat roof is subject to the following uniformly distributed loads: a dead load of 29 psf (pounds…

A: Given data - DL = 29 psf Lr = 12 psf SL = 13.5 psf WL = 22 psf Find out - 1) If load and resistance…

Q: In order to estimate in-situ compressive strength, Rebound Hammer test is applied on a concrete…

A: Rebound hammer test data

Q: Then a roof is subjected to downward wind load, which one of the following multiplication factors…

A: When a roof is subjected to downward wind load, 0.9  multiplication factors for dead loads is…

Q: Perform the Seismic Analysis of the Pulo Senior Hgh School bldg. and consider the following: V…

A: Base shear is generally an estimate of the maximum obtained lateral force on the base of the…

Q: Calculate the lateral wind loads acting on the 8-story building, considering the wind is acting…

A: Given: 8 story building  North South Direction Area = 30 m x 15 m Wind speed = 100 km/hr

Q: Universiti plans to construct residential accommodation for students which located near the sea. Two…

A: The building walls are useful for transfer the loads to the foundation. The load-bearing capacity of…

Q: The roof of rigid gabled frames 5 meters on centers has a slope of 30 degrees. If the wind velocity…

A: The slope of the roof is θ=30°. The wind velocity pressure on the roof area is q =2.8 KPa. The…

Q: The wind blows on the side of a storage building, it is located on open flat terrain where the wind…

A:

Q: A residential building is sitting in Brisbane CBD area. The design life of the building is 50 years.…

A:

Q: A steel building has plan dimensions of 50m x 50m and it is 120 m tall. It is provided with brick…

A: According to given data  Plan dimension= 50 x 50 in meters and Height is 120m

Q: (b) Determine the wind pressure distribution on the four sides of the four-story building below…

A: Vd = design wind speed = 140 mph Exposure D applies.G = gust factor = 0.85I = Importance factor =…

Q: Problem- For design of a roof truss, if the design wind velocity is 20 m/s, what is the design wind…

A: Given- Design wind velocity V=20 m/s, Design wind pressure=?

Q: According to the Working at Height Regulations, state: a) the minimum height at which precautions…

A: Working at heights means that the labor is working at a certain height above ground level and if…

Q: Example 4.1 A two-story essential facility shown in Figure 4.6 is an enclosed wood-frame building…

A: Wind is a mass of air that moves in a mostly horizontal direction from an area of high pressure to…

Q: Compute the vertical offset at a point on the curve 100m from the PVC.

A: Answer Based on the given data, we can determine the Vertical offset at a point on the curve 100 m…

Q: Anemometers at 2.5m and 40m on a tower record wind speeds of 2 and 5m/s respectively. What will be…

A: Wind speed at 2.5m (V2.5) = 2 m/s Wind speed at 40m (V40) = 5 m/s Determine the wind speed at 5m.

Q: Design Example: Calculations for Gust Effect Factor C.

A:

Q: Determine the LRFD factored load for the following situations on a steel column (Ignore any roving…

A: Factored load : A service load multiplied by a load factor yields factored design loads. Service…

Q: g Classification/Category: Section 103 Table 103-1 2. Basic Wind Speed: Figure 207A.5-1A,B,C 3.…

A:

Q: A roof design supports a dead load of 50 lb/ft² and a snow load of 30 lb/ft² In addition, a wind…

A: D = Dead load = 50 lb/ft2S = Snow load = 30 lb/ft2W = Wind pressure = 15 lb/ft²       (-ve for…

Q: Wind blows on the side of the enclosed agriculture steel building located on open flat terrain. If…

A:

Q: Please answer the problem in the picture, show all of your work and steps. Use the ASCE 7-16 as a…

A: Step 1: Determination of the allowable story drift ratio:According to ASCE 7-16, Table 12.12-1, the…

Q: In addition to the design snow load computed in practice problem 3, the roof of the building in…

A:

Q: Determine the fire endurance rating of the beam selected to carry the imposed loads. Extreme fiber…

A:

Q: A roof structure has a self-weight (dead load) of 0.23kPa, a snow load of 1.68kPa, and a 0.9kPa…

A: To determine the worst case for the given loads as per NBCC load combinations.   Given, Dead load…

Q: (a) The uniformly distributed live load on all four floors in figure below is 70 lb/ft² and…

A:

Q: A 1-mm diameter raindrop at standard temperature of 101.3 kPa and temperature of 20-degree C, using…

A:

Q: icture is made from concrete containing Type I The average ambient relative humidity is 70 percent.…

A: Relative humidity  = 0.7Moist cured for 7 daysf'c = 4000 psi

Q: -4 in. cinder fill -5 in. concrete slab ceiling

A:

Q: Situation No. 1: A 5 storey building is constructed with 15 ft. storey heights. The base shear has…

A:

Q: Calculate the dead and live loads (separately) applied on column D at the first floor Note:…

A: Calculate the dead and live loads (separately) applied on column D at the first floor Note:…

Q: To simplify the load determination, we will assume the Casper Hospital is a 210 ftx162 ft rectangle.…

A: The calculation procedure includes several middle steps, including calculating various other…

Q: For the Casper hospital, the weight of each floor is 2500 kips while the roof weighs 2700 kips. The…

A: Seismic activity causes the base of structures to experience lateral forces. Base shear estimates…

Q: utary areas of the ff: What are the Influence area of the ff: What are the unfactored and factored…

A: Factored Load = 1.2*DL + 1.3*LL                         = 1.2*2+1.3*4.8                         =…

Q: Identify the wind load accepted on the structure with following information: There is a hospital…

A: Solution: Given: Width(w0=60ft Length(L)=120ft Height(H)=20ft Wind Load=APCd where A is area of…

Q: Find the building's Seismic Response Coefficie

A: This question is from structural dynamics.

Q: Calculate the lateral wind loads acting on the 8-story building- considering the wind is acting…

A: Building dimensions- Wind speed, V= 100 km/hBuilding height, z= 25 mTo find - Wind pressure

Q: Please solve without using simplified wind pressure, and please use diagrams. Thank you .  A…

A: ANSWER IS GIVEN BELOW Explanation:FROM THE GIVEN DATA,I am already solved this Question previously…

Building codes

Building codes are the set of norms that contain all the standards for the construction of all the building and non-building structures. It is essential to follow the guidelines given in the building codes to get the project approved by the local authorities. The engineers, architects, contractors, and all the people involved in construction activities are obligated to refer to the building codes before performing any construction activity. In the United States of America (USA), The I-Codes, which are the International Building Code (IBC) or International Residential Code (IRC), electrical codes, plumbing codes, and mechanical codes are the model codes adopted. These model codes are updated after every three years.