Wile E. Coyote prepares a trap to kill (I hope so, too) Road Runner for good. What is the minimum and maximum pulling force of Wile E. Coyote on the rope to hold the 1-ton steel cylinder as shown while waiting for Road Runner to pass through? Show your answers in kN. The angle of friction between the pulley and the rope is 27°. Note: The shaded area of the pulley is 30 percent of the total area.

Q: F1= 10 kN F2 26 kN F4=44 kN E 30 FSAN

A: resolution of force F1 in x and y directionF1x=10cos45=7.07 KN→F1y=10sin45=7.07 KNupresolution of…

Q: Roller l Roller a al compute reactions @ A, B, C, D b) Draw shear and cl compute deflection @ A, B,…

A:

Q: A steel tape is standardized at 68°F under a tension of 15 lb when supported at the two ends only,…

A:

Q: The shear force at x = 1 m is...... kN. O 10 08 O 12 O 18 2 m 10 kN 3 m 8 kN

A: Shear Force is the transverse force which is parallel to the cross section of the beam.

Q: Three wheel loads rolls as a unit across a 12-m span. The loads are A = 15 kN; B = 25 kN, 2 m to the…

A:

Q: HAnd written and clean writing please Solve all parts

A:

Q: Problem 1: A structure is made of a horizontal beam AF and a weightless inclined bar CD with pinned…

A: Height of beam at A (h1) = 150mm = 0.15m Height of beam at F (h2) = 250mm = 0.25m Thickness of beam…

Q: A 2-ft-thick block constructed of wood (SG = 0.6) is submerged in oil (SG = 0.8), and has a…

A: Given:Thickness of wooden block= 2 ftThickness of aluminium plate = 2 ftSpecific gravity of…

Q: Determine the maximum negative bending moments at point B due to a concentrated live loads of 50 kn…

A:

Q: Situation 3: A wide flange Fixed ended beam has a span of 6 m. It carries a a concentrated load of…

A: span= 6 m Load= 135 kN UDL= 50 kN/m properties of wide flange- A=19000 mm2 d=432 mm bf= 264 mm tf =…

Q: Q2: Determine the reactions and check stability of Frame structure. 120 KN 10 KNm 6 KNim 1.75 kul…

A:

Q: a). What is the minimum diamétér of a solid 6m stéél shaft that will carry a shearing stress of not…

A:

Q: 5 KNIM 5KN 5m A

A:

Q: 4 kN - m ,2.0 kN/m B + I m 1 m

A:

Q: Situation #1: Compute for the force on member FG and identify if it is in tension or compression. 2m…

A: “Since you have asked multiple questions, we will answer the first question. If you want any…

Q: For what minimum value of the friction coefficient us will the arrangement of three identical…

A: given The coefficient of friction will be the same between all of the rollers and between the…

Q: 75 kN 140 kN 140 kN 140 kN 75 kN F 14 G 15 H 16 0 17 0 196 kN 3.30 m 5 6 7 9 11 12 13 8 10 D |1 3 E…

A:

Q: A 450mm x 650mm concrete beam is prestressed with a final prestressing force of 900kN at an…

A: Final prestressing force given = 900kn B= width of beam = 450mm D = Depth of beam = 650mm Direct…

Q: Q2/ PROBLEM 12.20 00 The flat-bed trailer camies two 1500-kg beams with the upper beam secured by a…

A:

Q: FORCE AND BENDING MOMENT CALCULATIONS WITH DIAGRAM, FIND ALL REACTIONS AND MOMENT USING THE FORCE…

A:

Q: 4) Select the size of a timber joist with notched end as shown below. The notch is set at 1/3 of the…

A: E(moduluoof elasticity of timber) = 9.5GPa

Q: a honzontal floor at A and on the wall at B making an angle of 60' from the horizontal. and the…

A:

Q: tude of reaction force at joint C of the hinge-beam show kN (round off to 2 decimal places). 3 m…

A: Beam is given fixed at A , Hinge at B and roller supported at CFIND reaction force at C

Q: It is show-and-tell day at Castle Greyskull and little She-Ra will tell the children about karate.…

A:

Q: The ratio of the theoretical critical buckling load for a column with fixed ends to that of another…

A:

Q: In beam test what is the advantage of a third point loading instead of using a single load in the…

A: Please refer the attached image for complete solution.

Q: Using the dred 206 N/m "The tect proper the EAR AND BEND maternizaterial or comunicat and the…

A:

Q: 1.om 0.8m 20 0.5 0.5 1.om

A:

Q: In the beam loaded as shown below, compute the moment of areas between support about the right end

A: To compute:The moment of areas between support about the right end

Q: • Two forces act on the hook. Determine the magnitude of the resultant force 30 200 N 40 500 N

A:

Q: 1. Given the figure below. The rivets are 25 mm in diameter. Calculate the maximum safe load P that…

A: Design in shear stress in rivets are given by ;

Q: A rope coupling device shown uses a pin 5 mm diameter to link the two parts. If the shear stress in…

A:

Q: com/webapps/assessment/take/take.jsp?course_assessment_id=…

A: Using formula to find angle of twist

Q: 1.50 in. 0.75 in. B A To 6.0 in. -15.0 in.-

A:

Q: correction to this exercice and explain in sentence or two why I made the mis

A: The Question is asking you to draw free body diagram for the given simply supported beam. Then we…

Finishing Operations

Finishing operations are the processes that are applied to the workpiece at the end of a manufacturing process, and after completing all other relevant operations that bring the product to its required dimensions. Finishing operations involve polishing, reducing the surface roughness, eliminating wrinkling, and grinding to enhance the surface texture and provide a better surface finish to the workpiece surface.