Wi 10 turns of wire on a cylindrical rod. He/she measures the diameter of the rod to calculate using a micrometer to estimate the needed wire length. If the reading of the diameter is given in figure, calculate the required wire for 10 turns. 3. 4. 5 6 Least significant bit= 0.05 mm, and zero error is 0. (Hint: a = 3, the length of the cylindrical bar is enough, and the windings do not overlap) A. 91.1 mm wire B. 83.7 mm wire C. 52.1 mm wire D. 62.4 mm wire E. 56.3 mm wire 1.

Q: Pin: MMC LMC Geom. Tol. с 1.000 1 1.000 Ø.515-.540 Hole 0.010M ABC 1.000 B Figure for Problem 21…

A:

Q: 45° FR F 75° 60 200 lb Using the sine rule, we have: O a F- 200lb Ob F- 273lb Oc F=189lb O d. F=…

A:

Q: Collect information on the American Wire Gage (AWG) standards. Create a table for annealed copper…

A: In USA a standard table is used for the collection of gauge wires made up of the annealed copper.…

Q: rof. Eduardo Stefanelli www.stefanell.eng.br 0 5 10 45 40 35 30 12.4 mm

A: The Screw gauge is given.

Q: Q1) A solid steel shaft subjected to a moment M. The shaft diameter is 60 mm. A Wheatstone Bridge…

A:

Q: In the following figure, add the tolerance zone and limits of size for both parts.

A:

Q: A pressurized vessel (closed ends) with 500 bar, its dimensions are L=1m, d = 25 Cm, D = 32 Cm, o, =…

A: Internal pressure (P) = 500 bar = 50,000,000 PaDiameter of the vessel (D) = 32 cm = 0.32 mInside…

Q: Hello, I don't understand how to solve 5-19 in the photo below. Because I can't find the correct…

A:

Q: If the tolerance in the figure below is for a pin .525 in diameter, what is the total positional…

A:

Q: 3. The plot below of load vs. extension was obtained using a specimen (shown in the following…

A: detailed explanation for each section are as follows :- (a) Yield Stress:-The stress at the yield…

Q: Suppose we are considering a ductile material under a static load. For the same geometry, same…

A: The given problem is based on theory of failures:

Q: If the pin in the drawing below is produced at Ø.498, what is its total positional tolerance? C…

A: Given data as per the question Pin diameter =0.498

Q: 8. For the following diagram, calculate the force needed to stretch the wire AB by 5%. Wire is A-36…

A: For the following diagram, calculate the force needed to stretch the wire AB by 5%. Wire is A-36…

Q: I need help solving problem numbers 4--15.

A: Hello, thanks for the question. Since we only answer up to 3 sub-parts, we’ll answer the first 3.…

Q: A B D (a) If the gap, w, must be at least 0.015 in for the proper functioning of the assembly, what…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.