While in lab, you find that your liquid begins to vaporize at 98.2°C. After finishing the experiment, you calculate (and obtain from another group) the following molar mass values. Calculate the standard deviation for the following the molar masses. Report your answer with two places after the decimal. Note: Copying and/or posting this question without the express written permission from Dr. Burke and the Department of Chemistry & Biochemistry at the University of Delaware is a violation of intellectual property copyright law. Data Table Trial #Molar Mass 1 2 3 4 100.63 100.44 101.06 99.63

While in lab, you find that your liquid begins to vaporize at 98.2°C. After finishing the experiment, you calculate (and obtain from another group) the following molar mass values. Calculate the standard deviation for the following the molar masses. Report your answer with two places after the decimal. Note: Copying and/or posting this question without the express written permission from Dr. Burke and the Department of Chemistry & Biochemistry at the University of Delaware is a violation of intellectual property copyright law. Data Table Trial #Molar Mass 1 2 3 4 100.63 100.44 101.06 99.63

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

5. Which term is INCORRECTLY defined? a. linear range - the range over which the response of an analytical method is proportional to analyte concentration b. dynamic range concentration range over which there is a measurable response to analyte, though the response is not linear c. blank solution - a solution containing all reagents and solvents used in the analysis to which no analyte is deliberately added d. standard solutions - solutions for which the standard deviation is known - 6. True or False: Internal standards correct random error caused by run-to-run variation. a. True b. False
If it was discovered that a polyaromatic hydrocarbon (PAH) having a density of 1 g/cm3 has a concentration of 1 ppm in the soil, how much soil would be required if a standard deviation of 0.1 is desired for the fundamental sampling error?
A quantitative analysis for an analyte gives a mean concentration of 12.6 ppm. The standard deviation due to the method, sm, is found to be 1.1 ppm, and that due to sampling, ss, is 2.1 ppm. By how much does the overall variance change if sm is improved by 10% and ss is improved by 15%?
An analysis where we know what analytes we are looking for is called An analysis where we do not know what analytes are in the sample is called a An example is A) untargeted, confirmation, targeted, Comprehensive drug screen B) targeted, confirmation, untargeted, comprehensive drug screen C) targeted, comprehensive drug screen, untargeted, confirmation analysis. An example is analysis. ▪ True or false: The purpose of the internal standard is to make quantitation of the analyte insensitive to injection errors
An ore sample was analyzed for its Fe content. Student A analyzed the sample a total of six times and her results had a standard deviation of 1.33. The same sample was analyzed five times by Student B and his results had a standard deviation of 3.42. To determine if their standard deviations are similar, they perform an F test. The calculated F value is and the table value of Fis 3 in your book for critical values of F. O 6.61; 7.39 O 6.61; 9.36 O 0.151; 9.36 O 2.57; 7.39 O 6.61; 6.98 Refer to Table 4-
In a particular trial, a student got a value for R of 0.083. Calculate the percent deviation of this result. Enter a number without the % sign. The percent deviation should be reported as a positive value.
Often the analyst will compare known quantities of analyte to unknown quantities of the material to be analyzed. This may be done in one of three ways: -use calibration curves; use standard additions; or use internal standards. The method of standard additions would be used when A) the quantity of sample analyzed or the instrument response varies from run to run. B) the standard solutions and the unknown solution all have similar characteristics are unaffected by the other material in the sample. C) the sample composition is unknown or complex and affects the analytical signal.
The results obtained by two analysts for the lead content of samples obtained at different certified points in Rustenburg are as follows: Analyst 1 – 79.22, 79.41,79.66, 79.45 Analyst 2 – 79.09, 79.08, 79.25, 79.13, 79.10, 79.19 Using the equation, calculate the following 1.the standard deviations 2 .the mean values of the two sets of data and 3. s-pooled
3. A chemist used two different methods to measure the number of mg of Fe in five iron(II) sulfate supplement tablets. The results of each are shown below. 64.71mg Method 1: 65.03mg 61.55mg 64.9 mg 65.1 mg Method 2: 65.5 mg 66.1mg Calculate the average amount determined by each method as well as the standard deviation and RSD for each method. 63.07mg 65.4mg 67.15mg Which method gave more precise results? How do you know? Is it possible to know which method is more accurate? Why or why not?
Which of the statements below are TRUE regarding the mean and standard deviation? I As the number of measurements increases, x approaches u if there is no random error. II The square of the standard deviation is the average deviation. III The mean is the center of the Gaussian distribution. IV The standard deviation measures the width of the Gaussian distribution. O land I Il and II O , Ill and IV O Ill and IV
Calculate the sample standard deviation, s, for this set of data: 1.9, 1.5, 6.0, 2.0, 1.4, 1.2 Report your answer to the fourth decimal place.