While filling up your car with gasoline, you notice that it takes 2 minutes to dispense 15 gallons of gasoline. What is the mass flow rate if water has a density of 10009/m 3 and gasoline has a specific gravity of o.72? O a. 3.4*/sec O b. 0.34k/sec O . 5400KE/sec O d. 54k/sec

Q: In a horizontal pipe, a pitot-tube with u-tube manometer (filled with water) has been attached to…

A:

Q: To measure the mass flow rate of water flowing in a pipe, an orifice is used and a water-mercury…

A: The volumetric flow rate of water is to be calculated.

Q: 7. An air balloon filled with helium gas is carrying two people. Assuming the air balloon to be a…

A:

Q: The tank in figure below is filled through point 1 with velocity equal to 5 m/s and point 3 with…

A:

Q: A pipeline carries petroleum at the rate of 795 m³/s from petroleum-well to the tank farther. The…

A: Given,  petroleum is goes well to tank at different pressure level.

Q: Q2 (30%) Pictured below is a tank containing salt water and a layer of light lubricating oil. The…

A:

Q: A pipeline laid cross country carries oil at a rate of 795 m3/s. The manometric pressure of the oil…

A: Given, Rate at which oil is carried=795 m3/s Manometric pressure of the oil leaving pump station…

Q: You have to measure the flow rate of water through a small pipe. In order to do it, you place a…

A: The volume and time data for a fluid flow through a small pipe is given.

Q: 1. A fluid in the manometer has a density of 1,259.9 ; Ry at 300 K. The m3 barometric pressure is…

A: Given data: Density of manometric fluid = 1259.9 kg/m3 Barometric pressure = 1.1 atm Absolute…

Q: Air enters a device at 7 MPa and 420°C with a velocity of 220 m/s. The inlet area is 70 cm? and the…

A:

Q: Water is flowing in a fire hose with a velocity of 1.0 m/s and pressure of 200,000 Pa. At the…

A: Inlet velocity (V1) = 1 m/s Pressure (P1) = 200000 Pa Pressure (P2) = 101300 Pa h1 = h2 Density (ρ)…

Q: For the Fig shown determine specific gravity of gauge liquid B if the gauge pressure at A is – 18…

A:

Q: A water pump is used to move water from one large reservoir to another large reservoir at a higher…

A: The operating flow rate is 6.33 L/min and the operating pump head is 5.77 m.Explanation:Here's how…

Q: Air with a mass flow rate of 600 kg/s is compressed at constant temperature with an initial pressure…

A: (a) For constant temperature process, P1V1 = P2V2    ......(1)   Given initial pressure, P1 =…

Q: Water is pumped from a reservoir to a tank suspended 20 m above the reservoir. The water flows…

A: Water is pumped from a reservoir to another reservoir at 20 m height. Both the reservoirs are open…

Q: Shown below is an inverted U-tube which is used to drain alcohol from a tank reservoir. The bend of…

A:

Q: 2.1 If the tank must be able to hold all of the water from a storm that delivers 1" of rain, what…

A: Since you have posted a question with multiple sub-parts, we will solve first three sub parts for…

Q: 2) m long, and 3 m deep, as shown in the picture. The container is initially filled with 30,000 kg…

A: Note: Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: Liquid n-hexane (p = 659 kg/m3 ) flows at a rate of m = 0.9 kg/s in a pipe with %3! inside diameter…

A:

Q: Seawater enters a tank at a volumetric flow rate of 9 L/h and with a salt concentration of e2t kg/L…

A: Input flow rate of seawater, Qin = 9 L/h Input concentration of salt in input stream, Cin = e2t kg/L…

Q: Air flows through a pipe, with a mass flow rate of 0.8 kg s-1. A static Pitot be is positioned at a…

A: m*(mass flow rate )= 0.8kg.sec-1Pstat= 4.013barI.D=50×10-3mM.W of air= 29 kg.kmol-1PStag=?

Q: Flow of Liquid in a Pipe and Mass Balance.

A:

Q: 8. Calculate the ft3/s or volumetric flowrate of water being discharge at an open tank which is 3048…

A:

Q: The pressure at the top of the tank of jet fuel is 180.6 KN/m². The depth of the liquid in the tank…

A: Given data: The pressure at the top of the tank of jet fuel= 180.6kN/m2 The depth of the liquid in…

Q: 7) Water is flowing upward at 1.676 m/s through a vertical piping system consisting of 3" sch40…

A:

Q: A water container is kept on a weighing balance. Water from a tap is falling vertically in to the…

A: This question is based on Dynamics of fluid flow. Given : Q = Volume flowrate of water from the tap…

Q: 23. A MUAUmeTer connects an oil pipeline anda water pipeline as shown in Figure. Determine the…

A: The pressure points in the figure is mentioned and we know that the pressure at point 2 will be…

Q: P. atm 0.5 m, 40° 0.4 m 60° 0.4 m 3 m 3 m 2.6 m A. | 0.3 m all in meters 0.5 0.5 0.5 -2.7 m- 1 m

A:

Q: Shown below is an inverted U-tube which is used to drain alcohol from a tank reservoir. The bend of…

A: Bernoulli's principle is applied to study the dynamics of the fluid. This law states that the speed…

Q: Extracted cane juice from a sugar mill flows through a 75 mm ID pipeline. Extracted cane juice is at…

A: Given Pipe diameter, Da=75mm T=15°C Throat diameter,Db=4/15 of pipe diameter h=500mm Differential…

Q: An incompressible liquid (specific gravity = 0.7) is being transported along a horizontal,…

A:

Q: A pressurized tank of water has a 10-cm diameter orifice at the side bottom corner of the tank,…

A: Density of water = 1000 kg/m3

Q: B) The pressure drop 'p' in a nozzle depends upon the velocity 'v' of a liquid leaving and the…

A: The pressure drop in a nozzle is P. The velocity of the liquid leaving the nozzle is v. The density…

Basic Chemical Calculations (Process and Variables)

A basic chemical calculation involves the application of the law of chemical proportions to various reactions and material and energy balance calculations on various chemical processes. Basic chemical calculation helps students analyze various chemical processes and develop problem-solving skills. The chemical manufacturing processes are divided into unit operations involving physical changes of material and unit processes involving the chemical transformation of materials. For instance, fluid flow, heat transfer, and mass transfer are unit operations, and oxidation, reduction, and pyrolysis are unit processes.