Which one of the following relation relating circular pitch and diametral pitch? Select one: O a. P. +P,= O b.P. P," O C.P =n/ Pa 2 O d. P,P.=n

Q: Determine Iy. 50 mm 50 mm 300 mm 50 mm y -200 mm an -X We Problem 4

A:

Q: Question 29 Which of the following can change the hardness of a material? O Manufacturing process O…

A:

Q: %o change in diamefesx-?

A: Given; Solid cylinder of; diameter,d1=120 mmheight,h1=50 mmTwo frictionless flat dies to a…

Q: Determine the y_bar coordinate of the composite shape. Treat the bent corners as square and ignore…

A:

Q: pered gibs are adjusted by screws spaced out along the length of the gib

A: The statement mentions "Tapered gibs are adjusted by screws spaced out along the length of the gib".

Q: の5 の25 23

A: Representation of three-dimensional object in two dimensional is known as an orthographic…

Q: 12-x2 了了少 Je

A:

Q: If A=0.375 inch, B=0.923 inch, C=1.0992 inches, find G A 기사 W -|×|-> G- -B- -C- F E-

A: If A= 0.375 inch, B=0.923 inch, C=1.0992 inches,find G.

Q: 1.Forging is a process that uses application of force to give shape to metal.

A: Forging is a process that uses application of force to give shape to metal. Answer: True

Q: write any 10 mechanical propeties of mild steel. Also expplain each one by one

A: 10 Properties of Mild Steel  1.Ductile material:- Can easily convert into thin sheet. 2.Easily…

Q: The Taylor's tool life component is 0.3 and constant is 120 for a cutting tool A and 0.5 and 30 for…

A: Given:nA=0.3CA=120nB=0.5CB=30

Q: Die Ntef d CW ad d 107 30T 167 327

A:

Q: 1. The built-up beam pictured on the right is subjected to an internal moment of M = 75 kNm. a) At…

A: *The internal moment acting on the structure is M=75 kNm. *The total length of the T section is…

Q: What is the formula of Hooke's Law?

A:

Q: Place the labels with the most accurate description on the micrograph at locations A, B, and C, as…

A: given; Place the labels with the most accurate description on the micrograph at locations A, B, and…

Q: P? P G P

A:

Q: pr... below. 5) Sketch the appropriate sectional view on the front view of the part

A: Given:To find:Sectional view on the front view.

Q: tan30*sin30

A: Given, Value of tan30 and sin30 is, tan30°=0.577sin30°=0.5

Q: A cross-section of a beam is shown in Figure Q2. If the shear force in this section is V = 180 KN,…

A: Given : The shear force in this section is The diagram is,

Q: Calculate the linear speed of the needle at the instant that theta equals 30 degrees and the wheel…

A: To find - The linear speed of the needle at the instant that theta equals 30 degrees and the wheel…

Q: Label all forces that act on the metal

A: A piece of metal is submerged in the liquid and one end of the metal piece is fixed with a string.…

Q: A hammer is balanced at the point "A", close to the metal part. If this hammer is then cut along the…

A: Consider the diagram shown below for the hammer with the center of masses for each side.

Q: Degree of drawing is measured in terms of; Reduction in strain Reduction in area O Reduction in…

A: Degree of drawing is measured in terms of: Answer: Reduction in area

Q: The planetary gear system of automobile. Consider that the crown R rotates as shown clockwise at 750…

A: Given: The gear train is shown below:

Q: Filler rod material is same base metal used in gas welding process. Select one: True False

A: Above statement is true.

Q: Customary units by using the values listed for length and mass as defined values: Bending moment or…

A: As moment bending moment or torque has two variables, force and distance. So, M = F × r…… (1) The SI…

Q: RIS R12 frant sew R32

A: Given 3D model To find Three views

Q: What is the Neutral Axis?

A: The neutral axis is the fiber of the beam with no normal stress. When a beam is subjected to a…

Q: When does a couple of moment work?

A: A couple is when a system of forces has no net force but has a net moment. A couple causes pure…

Q: The L2 steel bolt as shown in Figure 4 has a diameter of 5 mm, and the link AB which is made from…

A:

Q: raw the sectional view

A: According to the details provided in the question, we need to draw a sectional view according to the…

Q: symmetry

A: ANSWER: False statement-  option d) A centroidal axis is an axis of symmetry

Q: 2 Brass expands more than iron when heated. How would the strip look after prolonged exposure to…

A:

Q: A force F = 6980 N acts upon a piston head, as shown in the figure. The gudgeon pin G connects the…

A:

Q: Calculate y, the distance from the base to the position of the Neutral Axis of the T-section shown…

A:

Q: 2) Which of the following pairs are NOT correctly matched? Macro stresses - Large scale and may be…

A: Solution:

Q: Mr. Ahmed wants to replace his car door, for this purpose he has selected cast iron. Select one:…

A: IT IS FALSE.

Q: Number of links? The value must be a number 8 Number of full joints (J1)? Figure 2 Figure 2

A: Given mechanisms,

Q: During the governor regular working time the sleeve moves up with 16mm due to the effort of 225N…

A: Given that, The effort of the governer, F=225 N and the movement of the sleeve is, x=16 mm=0.016 m,

Q: 3. Write the information from the following weld symbol.

A:

Q: What is the radius equivalent to Mohrs Circle?

A: Method to construct Mohr's circle, First Plot point A σx,-τxy, & B σy,τxy on σ - τ plane. Now…

Q: Draw the front, Side and top

A: According to the question we need to draw the three orthographic projection views of the given…

Q: Write the flexure formula?

A: Flexure formula This formula is used to determine the internal bending stress when an external force…