3. Write the information from the following weld symbol.

Q: A fillet weld can be used to join which of the following joint types: *

A:

Q: Discuss the standard location of elements of a welding symbol.

A: Welding symbol that goes on the reference line to show the shape of welds, such as plug or filler.

Q: What are the grooves most often used for welding on mild steel pipe

A: Single V Single U Single J Single bevel grooves

Q: I need answers to parts 13, 14, and 15, pertaining to the print provided.

A: What is the smoothest surface finish specified on this print?Refer note, generally 6.3 is given to…

Q: Mention the basic flame types a

A: Given: Basic Flame types

Q: During the Brinell harness experiment, it is found that the diameter of indentation diameter is…

A: Answer:

Q: Why should there be a space between the plates whenmaking a fillet weld on thick plates of a tee…

A: Fillet welding refers to the process of joining two pieces of metal together when they are…

Q: Calculate the heat input during the arc welding process, if the voltage is 28 volts, current is 114…

A:

Q: What two units are used to show the minimum shearstrength of a spot weld?

A: Resistance welding comes in the form of spot welding. One of the simplest and quickest methods of…

Q: Which of these welds could be analyzed using the AISC Code's "kips per inch" method? (Indicate all…

A: AISC stands for American institute of steel construction.It is basically quality management system…

Q: Find the eccentricity of the welded connection by using 5 mm fillet weld. -120 mm - 200 mm 400 mm X-…

A:

Q: xplain the short circuiting arc weld cycle. NOTE:4-5 SENTENCES ONLY

A: Short circuiting arc weld cycle:  Short circuiting arc welding is a mode of metal transfer with low…

Q: 20

A:

Q: What is the procedure of using the Mohr's circle?

A: The procedure of Mohr's Circle is given as, (1) Draw the vertical and horizontal coordinates. The…

Q: Note: the drawing below shows the end view of a weldment consisting of 7 tubes. 8.625" 4. What is…

A: It is required to determine c to c distance

Q: After the weld is set up and ready to begin, how mightthe welder want to check for freedom of…

A: Welder method for determine the degree of freedom

Q: is the welding process in which two pieces to be joined are overlapped and placed between two…

A:

Q: Question 1 Figure Q1a shows two cables attached to a half-ring anchor point as shown in Figure Q1a.…

A: 1-Use resultant formula of 2 force to solve first problem, 2- use equilibrium equilibrium to solve…

Q: 57. In gas welding process, rubber is used as preferred material for hoses. Select one: True False

A:

Q: B: From figure 1, draw and explain the meaning of present symbol.

A: Solution:   Note: Dear Student! As per our guidelines, we are only allowed to answer a single…

Q: In most cases, pre-loading a bolted tensile joint increases the fatigue factor of safety. has no…

A:

Q: List the five joint types used in welding

A: Butt joint It is a kind of welding where the edges are joined together.  This has no impact on the…

Q: Seam-welding is .6 Multi-spot welding process Continuous spot welding process Used to form mesh )…

A: Seam welding is a type of resistance welding in which two rollers act as electrode between which…

Q: 7) On increasing the diameter of the SAW electrode, keeping the same current and arc length Width of…

A: The depth upto which the fused metal extends within the base metal or the pass from the previous…

Q: Who is ultimately responsible for the welder’s safety?

A: Welding is a process in which a large amount of the gasses and heat released if all these are not…

Q: 9. How much cast-iron welding rod is required to weld a 2-ft- long, single 60° V-groove joint in…

A:

Q: a. Show how the extent of the surfacing weld is indicated between the vertical centerlines in the…

A: Writing the procedure to organise the weld between the lines on the flat. (1) Let us consider that…

Q: A ball and a socket joint forms a

A: A ball and a socket joint is a form of synovial joint in which socket swivel around the fixed ball.…

Q: use 3 sig figs pls

A:

Q: Hello, I need to solve this exercise. Please, I am about to take exams and I need to solve some…

A:

Q: Question 1 A 50 kN load is transferred from a welded fitting into a 200 mm Figure 1. steel channel…

A:

Q: 12)In a fillet weld, if the leg length of the weld is 5 mm then the throat thickness is equal to: O…

A: The length of the weld is given by L=5 mm

Q: if a weldment is heated to correct distort from welding, the maximum localized he

A: if a weldment is heated to correct distortion from welding, the maximum localized heat shall not…