Which of the following statements correctly describe torque? The largest torque that can be provided to a lever arm is when the force is applied at an angle of 180°. Net torque is a conserved quantity. Angular momentum is a conserved quantity. A longer lever arm will result in more torque being applied to the center pivot. An empty soup can rolled down the same incline as a full soup can will reach the bottom first. Applying a torque to rotate an object will always result in an acceleration.

Which of the following statements correctly describe torque? The largest torque that can be provided to a lever arm is when the force is applied at an angle of 180°. Net torque is a conserved quantity. Angular momentum is a conserved quantity. A longer lever arm will result in more torque being applied to the center pivot. An empty soup can rolled down the same incline as a full soup can will reach the bottom first. Applying a torque to rotate an object will always result in an acceleration.

Glencoe Physics: Principles and Problems, Student Edition

1st Edition

ISBN:9780078807213

Author:Paul W. Zitzewitz

Publisher:Paul W. Zitzewitz

Chapter8: Rotational Motion

Section: Chapter Questions

Problem 2STP

See similar textbooks

Similar questions

Today, waterwheels are not often used to grind food. Instead, we have electrical devices such as blenders, choppers, and mixers. The electric motors in these devices are similar to a waterwheel, but instead of falling water causing the wheel to spin,electricity causes a shaft to spin. The specifications on a particular electric motor reports that at 1.75 103 rpm, it puts out5 hp. What is the corresponding torque in N m?
An automobile engine can produce 200 N m of torque. Calculate the angular acceleration produced if 95.0% of this torque is applied to the drive shaft, axle, and rear wheels of a car, given the following information. The car is suspended so that the wheels can turn freely. Each wheel acts like a 15.0 kg disk that has a 0.180 m radius. The walls of each tire act like a 2.00-kg annular ring that has inside radius of 0.180 m and outside radius of 0.320 m. The tread of each tire acts like a 10.0-kg hoop of radius 0.330 m. The 14.0-kg axle acts like a rod that has a 2.00-cm radius. The 30.0-kg drive shaft acts like a rod that has a 3.20-cm radius.
A force of F=(2.00i+3.00j) N is applied to an object that is pivoted about a fixed axle aligned along the z coordinate axis. The force is applied at the point r=(4.00i+5.00j)m. Find (a) the magnitude of the net torque about the z axis and (b) the direction of the torque vector .
The fishing pole in Figure P10.22 makes an angle of 20.0 with the horizontal. What is the torque exerted by the fish about an axis perpendicular to the page and passing through the anglers hand if the fish pulls on the fishing line with a force F=100N at an angle 37.0 below the horizontal? The force is applied at a point 2.00 m from the anglers hands. Figure P10.22
A constant net torque is applied to an object. Which one of the following will not be constant? (a) angular acceleration, (b) angular velocity, (c) moment of inertia, or (d) center of gravity.
Answer yes or no to the following questions. (a) Is it possible to calculate the torque acting on a rigid object without specifying an axis of rotation? (b) Is the torque independent of the location of the axis of rotation?
A uniform cylindrical grindstion has a mass of 10 kg and a radius of 12 cm. (a) What is the rotational kinetic energy of the grindstone when it is rotating at 1.5103rev/min ? (b) After the grindstone’s motor is turned off, a knife blade is pressed against the outer edge coefficient of kinetic friction between the grindstone and the blade is 0.80. Use the work energy theorem to determine how many turns the grindstone makes before it stops.
What force must be applied to end of a rod along the x-axis of length 2.0 m in order to produce a torque on the rod about the origin of 8.0k Nm ?
Find the net torque on the wheel in Figure P10.23 about the axle through O, taking a = 10.0 cm and b = 25.0 cm. Figure P10.23
A competitive diver leaves the diving board and falls toward the water with her body straight and rotating slowly. She pulls her arms and legs into a tight tuck position. What happens to her rotational kinetic energy? (a) It increases. (b) It decreases. (c) It stays the same. (d) It is impossible to determine.
Calculate the rotational kinetic energy of a 12-kg motorcycle wheel if its angular velocity is 120 rad/s and its inner radius is 0.280 m and outer radius 0.330 m.
The combination of an applied force and a friction force produces a constant total torque of 36.0 N m on a wheel rotating about a fixed axis. The applied force acts for 6.00 s. During this time, the angular speed of the wheel increases from 0 to 10.0 rad/s. The applied force is then removed, and the wheel comes to rest in 60.0 s. Find (a) the moment of inertia of the wheel, (b) the magnitude of the torque due to friction, and (c) the total number of revolutions of the wheel during the entire interval of 66.0 s.