The length of a bicycle pedal arm is 0.152 m. If a downward force of 85 is applied to the pedal by the rider at an angle of rotation of the pedals 30 degrees from the vertical determine the torque exerted on the bicycle. Hint: Draw a sketch to make sure you have the angles right. The correct units for torque are Nm.
Q: Force F, acts half as far from the pivot as F. What magnitude of F, causes the net torque on the rod…
A: Force F2 acts half as far from the pivot as F1. What magnitude of F2 causes the net torque on the…
Q: A square metal plate 0.180 m on each side is pivoted about an axis through point O at its center and…
A: Given data: Let us consider the given data a square metal plate is 0.180 m The given force is…
Q: 2. Calculate the net torque (magnitude and direction) on the beam in the figure below for the given…
A:
Q: 105 N 3D 1.00 m 1
A:
Q: no ai please
A: Given that the torque produced by a couple is not dependent on the point of application, the torque…
Q: Two equal forces are applied to a door. The first force is applied at the midpoint of the door; the…
A:
Q: In the following figure, a force of 20 N is going to be applied to the rod that has a length of 15…
A: Given : Force applied : F = 20 N Length of rod : L = 15 cm Required : Location for maximum torque…
Q: 5. (8 pt) Balls are attached to light rods and can move in horizontal circles as shown in the…
A: In the 1st figure angle between r and F =90degree.so Torque1 =rFsin90°=rF. In the 2nd figure angle…
Q: Look at the diagram below. The weight of the grapefruit is 15 N. Calculate the moment of this…
A:
Q: What is a necessary condition for a body to be in rotational equilibrium? B.) What happens to an…
A: To find Condition for body to be in rotational equilibrium The object when a net torque applied on…
Q: QUESTION 2 Which statements about torque are correct? Choose all that apply. Positive torques result…
A: The torque which is responsible for circular motion of any object is basically the radial…
Q: The plywood sheet shown in the figure below measures 2.0 m x 2.0 m, and each of the four forces the…
A:
Q: The fishing pole in the figure below makes an angle of 20.0 ° with the horizontal. What is the…
A:
Q: Enter to 3 significant figures = TF3 -10.8 = -9.35 TFA TF₂ (d) Between F₂ and F4 which force…
A:
Q: A child with a mass of 25 kg sits at a distance of 1.8 m from the pivot of a seesaw. Calculate a.…
A:
Q: The forearm in the figure(Figure 1) accelerates a 3.9 kg ball at 6.1 m/s? by means of the triceps…
A: Given- mass of ball , mb= 3.9 kg acceleration of ball , a = 6.1 m/s2 perpendicular distance of ball…
Q: 4. Two forces with equal magnitude F1=F2=8.00N are applied to a rod. -3.00 m a.) What should the…
A: The torque is the calculation of the external force acting on the object that causes the object to…
Q: This week in lab you observed how a force can apply a torque and rotate an object. Using the…
A: Step1: Overview Torque is known as the moment of force. In other words, it is the rotational…
Q: Explain why the student holding the pole is smarter than the other student. Be sure to use the…
A: answer student holding the the pole is smarter then the other student because (1) it increases…
Q: A sphere ROLLS SMOOTHLY down the incline. What can we say for sure? A) The normal force cancel the…
A: To determine A sphere rolls smoothly down the incline. What can we say for sure
Q: Assume all bones are massless in this approximation. You hold a dumbell m=22 kg as shown. Distance…
A:
Q: 1) Draw the free body force diagram. Use Newton’s second law and also the rotational version of…
A:
Q: What is the torque by the fire extinguisher about the center of the seesaw, in N-m? Use g = 10 m/s².…
A: Since you have posted multiple questions, we will provide the solution only to the first question as…
Q: Which of the following statements correctly describe torque? The largest torque that can be provided…
A: Torque is defined as
Q: Both the magnitude and the direction of the force on a crankshaft change as the crankshaft rotates.…
A:
Q: What happens to the torque due to the tension? Is your result consistent with the formula τ = R × f?…
A:
Q: For items 7-13 choose the letter of the best answer. No need to give explanations. 7. A force of 17…
A:
Q: The figure below shows forces acting at various points on a metal rod. The angles a = 40°, B = 31°,…
A: α=40oβ=31°γ=19°l=4.6 m
Q: A rod of Length 5R is fixed about a point 1/5th of the length from the right edge. All forces are…
A: In given figure 4 forces are applied on rod at different point. Torque = r × F = perpendicular force…
Q: a.) In the following free body diagram of the knee and lower leg, draw the moment arm (dw) for the…
A: Weight force is Fwt Muscle force is Fm
Q: Hinge 6. Two Identical twins pull on each side of a door that is 60 cm in length from hinge to end…
A: Solution:-Given that
Q: What is the direction of the torque produced by the force shown in the diagram? -z axis -y…
A: Given Force is at an angle to the x axis, in x-y plane Thus direction of the torque produced by…
The length of a bicycle pedal arm is 0.152 m. If a downward force of 85 is applied to the pedal by the rider at an angle of rotation of the pedals 30 degrees from the vertical determine the torque exerted on the bicycle. Hint: Draw a sketch to make sure you have the angles right. The correct units for torque are Nm.
Step by step
Solved in 4 steps with 1 images
- 1. In the figure below, forces A, B, C & D each have magnitude 50 N and act at the same point on the object. (a) What torque (magnitude and direction) does each of these forces exert on the object about point P? (b) What is the total torque about point P? 60 30 20 cm 60 C Di 10The free body diagram below represents a 1 500 kg car sitting on a 3 000 kg bridge supported at its far ends. The car's position is three quarters of the length L from the left end of the bridge. Identify the one error in the torque equation below: a. never produces a torque on the bridge no matter where the axis of rotation is placed. b. never produces a torque on the bridge no matter where the axis of rotation is placed. c. cannot produce a torque on the bridge no matter where the axis of rotation is taken since it is at the center of the bridge. d. Because the perpendicular distance to from the left end of the bridge is 0, F1L should be 0. e. Because the perpendicular distance to from the right end of the bridge is 0, F2L should be 0.What is the torque from the weight of the sphere about the center of the sphere? What is the torque from the frictional force about the center of the sphere?
- In the figure, what magnitude of force F applied horizontally at the axle of the wheel is necessary to raise the wheel over an obstacle of height h = 0.175 m? The wheel's radius is r = 0.648 m and its mass is m = 1.29 kg. %3D Number i UnitsA mechanic applies a force of 8N perpendicular to a 0.7m long wrench to tighten a bolt. a) How much torque does the wrench apply to the bolt? ✓✓ b) Explain a way that he could increase the amount of torque on the bolt. ✔Question in pic.
- The torque caused by a force F applied at a distance r from the axis of rotation, is given byt-rF sin e, whereq is the angle betweenf and. If the magnitudes r and F remain the same, what other angleq¢ will produce the same torque as was produced at angleq ifq was less than 90°? e' - 90° + e e' - 90° - e O e' 180° - e D None of the above.1. How can the same force applied to a lever produce different torques? A. By applying the force at different points of the lever arm along the length of the lever or by changing the angle between the lever arm and the applied force. B. By applying the force at the same point of the lever arm along the length of the lever or by changing the angle between the lever arm and the applied force. C. By applying the force at different points of the lever arm along the length of the lever or by maintaining the same angle between the lever arm and the applied force. D. By applying the force at the same point of the lever arm along the length of the lever or by maintaining the same angle between the lever arm and the applied force.What are the parameters that impact the magnitude of a torque? a) The magnitude of the force, the duration of the action and the angle of application of the force. b) The magnitude of the applied force, the angle at which it's applied and the distance at which it's applied from the axis of rotation. c) The magnitude of the force, the mass of the object and the duration of the action.
- Refer to the following figure when answering items 6, 7, and 8. The arrows represent forces acting on the bar. There are two answers per item- B -C D. F 6. Forces that result to clockwise torque about the axis 0 A. A and C C. E and F B. B and F D. B and D 7. Forces that result to zero torque about the axis 0 A. C and F C. A and F B. C and E D. B and C 8. Forces that result to counterclockwise torque about axis 0 C. A and F A. E and F B. C and D D. B and DIn opening a door, a 35.8 N force is applied as shown in the figure below. Find the torque produced by this force with respect to point O. (Let r = 0.920 m and 0 = 59.0.) magnitude direction clockwise FA string is tied to a doorknob 0.72 m from the hinge as illustrated in the figure. At the instant shown, the force applied to the string is 5.0 N. What is the magnitude of the torque on the door? ... hinge 33° String 57° 0.72 m doorknob A 0.78 N.m B) 2.1 N.m C 3.0 N.m D) 0.60 N.m