Which of the following examples are classified as either a solid-liquid extraction or a liquid-liquid extraction. Choose all that apply. Oa. A solid is formed by the addition of a solution of hydrochloric acid to a solution of sodium salicylate. Ob. A solution containing salicylic acid in diethyl ether is shaken with a 5% sodium bicarbonate aqueous solution in a separatory funnel.

Which of the following examples are classified as either a solid-liquid extraction or a liquid-liquid extraction. Choose all that apply. Oa. A solid is formed by the addition of a solution of hydrochloric acid to a solution of sodium salicylate. Ob. A solution containing salicylic acid in diethyl ether is shaken with a 5% sodium bicarbonate aqueous solution in a separatory funnel.

Appl Of Ms Excel In Analytical Chemistry

2nd Edition

ISBN:9781285686691

Author:Crouch

Publisher:Crouch

Chapter3: Statistical Tests With Excel

Section: Chapter Questions

Problem 6P

See similar textbooks

Similar questions

Preparation of sodium standard solutions with concentrations of 10, 20, 40, 60, 80, 100 (ppm) in a volume of 100 ml for each solution. [using a 100 ppm reference solution prepared from a weight of sodium chloride in a volume of 1 liter]
Solid-liquid extraction is an effective method to isolate a the desired soluble component in a solid mixture from insoluble materials in the mixture. True False
A reagent bottle contains 250 cm3 of 0,4 mol.dm–3 oxalic acid(C2O4H2) solution. Calculate the mass of pure oxalic acid thatmust be dissolved in this solution so that its new concentration is 0,6 mol.dm–3. Assume that the volume of the solution remainsconstant
1)What is the value of the Langmuir constant "a"? 2)What is the value of the Langmuir constant "b"?
Explain how you could separate an equimolar mixture of Compound A, B and C. (a flow chart). Organic solvent: ether,methylenechloride; Aqueous solution: HCI (ag),NaOH (ag), NaHCO3(ag)
A student was careful to make and stir all of her standard solutions immediately before measuring their turbidity for her calibration curve. However, she let her tap water solutions sit for 10 minutes prior to measuring their turbidity. If she measured the top portion of the solution, would her experimental sulfate ion concentration be higher or lower than it should be?
8, Q4
3. It is used to convert the known weight of the precipitate to the corresponding weight of the analyte. a. Gravimetric factor b. Mole ratio c. Mass ratio d. All of the choices 4. Which of the following is used to express the ppm of the solution? a. Kg analyte/liter solution b. Mg analyte/liter solution x 10^6 G analyte/ g sample x 10^6 d. Kg analyte/kg sample C.
16) Which of the following(s) is/are correct? I- Selectivity factor is the amount of time a solute spends in the stationary phase relative to the time it spends in mobile phase II- The retention time for an analyte is the time interval between its injection onto a column and its appearance at the detector at the other end of the column. III- Distribution constant is the ratio of the total solute concentration in the stationary phase to that in the mobile phase. A) I, II and III B) Only II C) I and III D) II and III E) Only III for GC2
A typical protein contains 16.2 wt% nitrogen. A 0.500-mL aliquot of protein solution was digested, and the liberated NH3 was distilled into 10.00 mL of 0.021 40 M HCl. Unreacted HCl required 3.26 mL of 0.019 8 M NaOH for complete titration. Find the concentration of protein (mg protein/mL) in the original sample.
You were given a mixture of two miscible solvent A and B that you are tasked to separate. You know that solvent A has a boiling point of 49 oC while solvent B has a boiling point of 174 oC. Which of the listed method would overall be the most efficient? Fractional distillation Recrystallization Solid-liquid extraction Liquid-liquid extraction Simple distillation Acid-Base extraction
A double indicator analysis of a soda ash sample was performed. The student weighed 0.4375 g of the soda ash sample and dissolved it to make 100.0 mL solution. The students then took a 25 mL aliquot of the sample solution, then added 25 mL H2O and performed double indicator titration. The phenolphthalein endpoint required 10.27 mL 0.04027 M HCl titrant. The sample was further titrated using Methyl Orange and took a total of 15.97 mL of the titrant to reach the endpoint. Given that the molar weight of Na2CO3 - 105.99 g/mol, NaHCO3 = 84.007 g/mol, and NaOH - 39.997 g/mol answer the following: a. What are the components of the soda ash sample? (The constituents of the sample came from Na2CO3, NaHCO3, and NaOH). b. What are the moles of each component in the titrated 25 mL aliquot? c. What is the percent composition in (% w/w) of each component in the soda ash sample?