Which of the following conditions describes an object in static equilibrium? a. Net forces and moments are equal to zero b. All forces and moments are equal to zero c. Upward forces equal to are downward forces d. Clockwise moments are equal to anticlockwise moments

Which of the following conditions describes an object in static equilibrium? a. Net forces and moments are equal to zero b. All forces and moments are equal to zero c. Upward forces equal to are downward forces d. Clockwise moments are equal to anticlockwise moments

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

4. Determine the mas that must be supported at A, and the angle ø of the connecting cable in order to hold the system in equilibrium. 60° A 30 kg 40 kg
10. One end of a 1.5 kg uniform stick that is 2.0 m long is placed against a vertical wall as shown. A light cord making an angle 0 with the stick holds the other end. The coefficient of static friction between the end of the stick and the wall is 0.500. a) What is the maximum value the angle 0 can have if the stick is to remain in equilibrium? Ө b) When 0 = 15° a body of the same weight as the stick is suspended from the stick a distance x from the wall. What is the minimum value of x for which the stick will remain in equilibrium?
A 4-m long, 150-kg steel beam is attached to a wall with one end connected to a hinge that allows the beam to rotate up and down. The other end of the beam is held in a horizontal position with a cable that makes a 27° angle with the beam and is attached to the wall (see (Figure 1)). a.What is the tension force that keeps this beam in static equilibrium? b. A mass of 75 kg is hung from the beam 3 meters away from the hinge (see (Figure 2)). Now what is the tension force that keeps this beam in static equilibrium? c.What is the vertical component of the force that the hinge exerts on the beam?
A uniform meterstick is supported at the 50 cm mark. A 25N weight is placed at the 10 cm mark. Where should a 200N weight be placed for the meter stick to be in equilibrium? a.1.25 cm mark b. 45.5 cm mark c. 51.3 cm mark d. 80.0 cm mark
11. The diagram below shows a ladder that is 6.0 m long and has a mass of 20.0 kg. The ladder rests on a level floor and against a wall at an angle of 15° to the wall. The coefficient of static friction between the ladder and the floor is 0.232. A person with a mass of 60.0 kg begins to climb the ladder. The base of the ladder will begin to slide away from the wall when the person reaches which distance interval from the base of the ladder? A. 0 m–1.5 mB. 1.5 m–3.0 mC. 3.0 m–4.5 mD. 4.5 m–6.0 m
Two forces are acting on an object. Which of the following statements are correct? a. The object is in equilibrium if the forces are equal in magnitude and opposite in direction. b. The object is in equilibrium if the net torque on the object is zero. c. The object is in equilibrium if the forces act at the same point on the object. d. The object is in equilibrium if the net force and the net torque on the object are both zero. e. The object cannot be in equilibrium because more than one force acts on it.
34. Please help answer this question thank you so much!:))
A. Find the required F to achieve Net Torque = 0. Assume b = 2a. B. After a design modification, all forces including F stay the same. If new design is basedon b = 1.5a, what will be the net torque after modifications?
6. A 5-meter long wire has a total mass of 0.65 kg. It is suspended by two uniform 200-N poles, which lean apart from each other, as shown below. Assume the only significant forces are the tension of the wire, the gravity of the earth, and a contact force with the ground below. 6. A 5-meter long wire has a total mass of 0.65 kg. It is suspended by two uniform 200-N poles, which lean apart from each other, as shown below. Assume the only significant forces are the tension of the wire, the gravity of the earth, and a contact force with the ground below. wire 60° 60° Calculate the velocity of a transverse wave traveling along this wire. Calculate the velocity of a transverse wave traveling along this wire.
3.) Consider the drawing below: Ť The 4.0-kg hinged rod is uniform and has a = 2.0m. The object at the end of the rod masses 8.0-kg. A wire affixed to the wall holds the rod horizontally. The wire makes an angle of 28° with the rod. a. Draw a picture. b. Draw a free-body diagram centered at the top of the loop. c. Use equilibrium considerations to determine the tension in the wire and the x and y forces on the rod's hinge.
5. A uniform 0.225 kg rod of 0.90 m length is used to suspend two masses as shown below. At what distance should the 0.40 kg mass be placed to achieve static equilibrium? 0.225 kg rod 0.65 m 0.25 m 0.40 kg 0.50 kg 6. If the 2.30 kg uniform beam shown in static equilibrium, what is the magnitude of
What is the normal force on the mass M = 7 kg in the figure if F 60N and the angle e= 30°? F Select one: A. 70 N B. 40 N C. 30 N D. 120 N E. 100 N Previous page Next page + Torque and Equilibrium Jump to... Chapter-9-Equilibrium of rigid bodies →