Which of the following assumptions is NOT necessary in concluding that the normal stress distribution is uniform over the cross-section of an axially-loaded member?   a. Material is homogeneous   b. Material is linearly elastic   c. The section to be analyzed must be sufficiently far from the point of application of load   d. Plane Sections remain plane and parallel to each other.

Q: H h d

A: To solve this, we need to find the permissible load at critical section that is at the section where…

Q: Answer: (a) ox= Oy= Txy= (b) Op1= Op2 = Tmax in-plane = psi psi psi psi psi psi

A:

Q: maximum normal stress that occurs

A:

Q: The section of a thick beam has the dimensions Calculate the section properties I,, I, and I,…

A: The direct stress is generally produced by bending moments or by the bending action of shear loads…

Q: and e, are the maximum and minimum strains, respectively in the If Ex neighbourhood of a point in a…

A:

Q: A cube (E - 20OGPA) is experiencing stress from all directions. Along the x-direction, there is a…

A:

Q: At a point in an elastic material, ,40 Nimm a direct tensile stress of 80 N/mm and a direct…

A:

Q: The stress state at a point in plane stress is shown in Figure Q5. Assume the yield stress of the…

A: Yield stress of ductile material = 275 MPaStress element:

Q: The normal and shear stresses acting on element A are 6,650 psi, 17,600 psi, and 2,700 psi (see part…

A:

Q: -termine the principal stresses, the maximum in plane d average normal stress. Specify the…

A: Since this a multiple question as per Bartleby policy, we can answer only first question, for other…

Q: 3. Determine the principal stress, the maximum in-plane shear stress, and average normal stress.…

A:

Q: Question A structural element is subjected to a two dimensional stress system, wherein ₁ = 225 N/mm²…

A: Given- Stresses- σ1=225 N/mm2,σ2=compressive,Possion's ratio μ=0.25, It is needed to find the value…

Q: Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid…

A: The given figure is shown below:

Q: At a point in a machine component that is subjected to plane stress, the normal and shear stresses…

A: Determine the strain components of machine?

Q: A beam with a T-section is supported and loaded as shown in the figure. The cross section has width…

A: A beam with the T section is given in the question all the loading condition is given in the above…

Q: Which of the following statements is FALSE? Select one: O A. The elastic torsion formula is…

A: Torsion:- Torsion refers to the twisting of a structural member under the action of torque or…

Q: A rectangle of an elastic material is deformed in the x, y plane as represented by the dashed lines.…

A: Given: E=300 MPa  and poisson ratio μ=0.4No deformation in Z directiona Normal strain strain in x…

Q: At a point in a machine component that is subjected to plane stress, the normal and shear stresses…

A:

Q: A stat of stress is specified in figure by using Mohr's circle determine the normal and shearing…

A: Given:Required:Normal and shear stress on principal planes and on plane having maximum shear stress.

Q: At a point in a machine component that is subjected to plane stress, the normal and shear stresses…

A:

Q: At a point in a machine component that is subjected to plane stress, the normal and shear stresses…

A:

Q: For a square cross-section bar affected by torsional moment at both ends, the streps components are…

A: σx=150σy=100zxy=-60σmaj/min=σx+σy2±σx-σy22+zxy2               =150+1002±150-10022+602…

Q: Element in plane.stress the stresses are and g, = 97 MPa, g, = 76 MPa and T= 22 MPa. Determine the…

A: Radius of the circleR=(σx-σy2)2+τxy2R=(97-762)2+222R=24.38 MPA

Q: Q. No 1. material. Discuss in detail the Stress Strain Diagram of ductile material and brittle |CLO…

A:

Q: Problem 4 : For the shown Mohr circle: a) What is the state of stress at the reference point A.…

A:

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…

A: Given data: Sx=-12 ksiSy=33 ksiSxy=17 ksi

Q: At a point in a machine component that is subjected to plane stress, the normal and shear stresses…

A:

Q: Which of the following best represents the distribution of the normal stress on the cross section of…

A: Problems details - Multiple choice questions -

Q: At a point in a component, the state of stress is shown on the element below. Assume that the stress…

A: Determine the magnitude of the absolute maximum shear stress that acts at the point.

Q: View Policies Current Attempt in Progress Mohr's circle is shown for a point in a physical object…

A:

Q: In a structural element, that is in plane stress state, the stress components are: Ox = 52 MPa, Oy =…

A: Given σx= 52MPaσy= -16MPaτxy=- 31Mpa

Q: For the state stress shown in figure below, determine the principle stresses and the maximum…

A:

Q: A state of stress is specified in the figure shown below. Determine the Normal stress (mPa) on the…

A: The normal stress on vertical plane, Px=-63MPaThe normal stress on horizontal plane, Py=-80MPaThe…

Q: Choose the correct one and explain it

A: Given data : Normal stress in X direction (σX)=5 MPaNormal stress in Y direction (σX)=5 MPaMajor…

Q: AExplain in a few words the difference between the normal stress, the shearing stress, and the…

A: What is stress: It is the internal resistance developed by the body to external load applied to it…

Planar Stresses