Which circuit performs the sampling operation in the beginning of the A/D conversion process? Sample-and-hold amplifier Flash converter Reference regulator Shift register

Q: In measurement system, are needed where the output variable of a primary transducer is in an…

A: The first element in any measuring system is the primary sensor: this gives an output that is a…

Q: A signal conditioning circuit is typically connected between the input source (typically a sensor)…

A: The question is from analog circuits.

Q: What are the input characteristics of the transducer? b)What is zero error of the transducer?…

A: a) While choosing a transducer for any application the input, transfer and output characteristics of…

Q: 3-why Demodulation is necessary ?

A: Note: As per Bartleby guidelines, we are supposed to provide solution of first question , I request…

Q: ..... .. .. ... .... ... In PCM, the first step after PAM, is coding of the analog pulses. Select…

A: We need to tell about the PCM .

Q: 5- Sampling theory 6- Nyquist rate 7- PAM 4-Pulse Code Modulation

A: Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: 8- Auto transformer is used in tuned amplifier to (transform low impedance of transistor input,…

A: 8.) In amplifier transformer is connected instead of collector load which serves as inter stage…

Q: D Question 10 When same input voltage is applied to each base of a differential amplifier, the…

A: The question is related to differential amplifiers-analog circuits

Q: The output transducer is also called as

A: Output Transducer

Q: Sample and Hold circuit is not required before the analogue to digital converter. A) True B) False

A: Sample -and -hold circuits in ADCs  are designed to stable the signal during the conversion process…

Q: Design 3-bit Binary Weighted digital to analog converter (DAC) with, R, R=15K2 and Vin =10

A:

Q: Colpitts oscillator and explain how it works.

A: Given:  1) Draw the Colpitts oscillator and explain how it works.    2) State the functions of all…

Q: The Buck converter exhibits a right half plane zero in the control to output transfer function? O…

A: The solution is given below

Q: 11. An SCR turn-off requires * anode current falls below holding current. reverse voltage is applied…

A: 17. An SCR turn off requires  a. Anode current falls below holding current. b. Reverse voltage is…

Q: Q 6(a) Derive state-variable equations for the circuit in Figure 6, showing all steps clearly and…

A: 6a)

Q: A 6.1-V analog input voltage is to be converted to digital using a 4-bit successive approximation…

A:

Q: b) Design a 6-bit binary weighted resistor DAC for the input of (101100)2. Assume Input Reference…

A:

Q: Draw a 5-bit R/2R ladder DAC circuit and calculate the analog value of the digital 01011 information…

A: Draw a 5-bit R/2R ladder DAC circuit and calculate the analog value of the digital 01011 information…

Q: Describe the differences between an LNA, a power amp, and a gain block.

A: LNA The full form of LNA is a Low Noise Amplifier. The LNA amplifies the signal at the time of…

Q: a) List five (5) methods of analogue signal conditioning.

A:

Q: 2. Consider the switching oscillator shown below built from a threshold-controlled inverting Schmitt…

A: Oscillator: An oscillator is an electronic device that consists of an op-amp with a positive…

Q: The parameter which acts as a control for switching a MOSFET is Gate Current Drain - Source Voltage…

A: MOSFET is a Metal oxide semiconductor field effect transistor  It is a transistor which can be used…

Q: The parameter which acts as a control for switching a MOSFET is Gate Current Drain - Source Voltage…

A:

Q: Which of the following is the circuit shown in the figure? Output Input a)a VCO b) a FM modulator c)…

A:

Q: Discuss the significance of analog-to-digital converters (ADCs) in microcontroller applications.…

A: The above question is based on the application of ADCs in microcontroller-based applications.

Q: describe and compare the different types of Analog to Digital Converters(Advantages, Disadvantages,…

A: Analog to digital converters are used within a data acquisition system is to convert conditioned…

Q: Q1: Answer the following: A. Design a square wave Oscillator for frequency 1 kHz using: (i) BJT.…

A:

Q: differential input single-ended output opamp

A:

Q: What is the physical meaning of sampling theorem? And Write down the corresponding expressions for…

A: Sampling theorem: It can be defined as " a continuous time signal can be converted into its samples…

Q: Draw a one-phase bridge type Full Wave Uncontrolled AC/DC converter circuit, explain the working…

A:

Q: For the given Vin (input voltage), calculate Dout (digital output) in decimal and binary, given the…

A:

Q: explain briefly the function of each part of the DSP system

A: It is given that:

Q: The figure below shows a block diagram for a typical measurement system. Match the blocks below with…

A:

Q: 1/1 The fixed bias provides good Q- Point stability. It is the most using .bias circuit False True

A: The fixed bias provides good Q-point stability.  It is the most using bias circuit.  True  False…

Q: Q2. Explain the analog to digital conversion process using digital technique employing sample and…

A:

Q: 11. Sketch the output of the following MOSFET sampling circuit:

A: For the given circuit as shown belowWe need to sketch the output.

Q: Q1/ Design a binary to Gray converter using a four- input, four-output PROM ?

A:

Q: State advantages of counter mode

A: Counter Mode -  The Counter Mode, sometimes known as CTR, is a simple counter-based block cypher…

Q: The 555 timer connected in the monosta le multivibrator mode: a) Design the circult to provide an…

A: The required value of resistor and capacitor needs to be calculated and the recovery time of the…

Q: How can the error amplifier control the output voltage of a buck converter? Please explain.

A: Types of DC-DC Converters Buck Converter Boost converter Buck-Boost Converter Flyback Converter…

Sample and Hold circuit

The sampling circuit and the holding circuit generate electrical samples as input and then hold these samples for a specified period. The time at which the sample and circuit holder produces the input signal sample is called the sampling time. Correspondingly, the length of the circuit that holds the sampled value is called the holding time.