When tunnel mode is used, a new outer IP header is constructed. For both IP4 and IPV6, indicate the relationship of each outer IP header field and each extension header in the outer packet to the corresponding field or extension header of the inner IP packet. That is, indicate which outer values are derived from inner values and which are constructed independently of the inner values.

When tunnel mode is used, a new outer IP header is constructed. For both IP4 and IPV6, indicate the relationship of each outer IP header field and each extension header in the outer packet to the corresponding field or extension header of the inner IP packet. That is, indicate which outer values are derived from inner values and which are constructed independently of the inner values.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

A router has the following Access Control List defined. Each line will be applied to the header of the packet, in order, until a match is found. If a match is found, the action (permit or deny) will be applied. ip access-list extended RemoteMgt permit tcp any host 192.168.1.100 eg 80 log deny tcp any any eq 80 permit ip any any This access will: O Allow any source address to reach 192.168.1.100 on port 80 Deny any source address from reaching any destination address on port 80 Allow all IP traffic from any source address to any destination address O Allow source address 192.168 1.100 to reach any destination address on port 80 Deny any source address from reaching any destination address on port 80 Deny all IP traffic from any source address to any destination address Allow source address 192.168 1.100 to reach any destination address on port 08 Deny source address 192.168.1.100 from reaching any destination address on port 08 Deny all IP traffic from any source address to any…
QUESTION 14 What is the minimum size of an IPv4 datagram header in octets (not including body field)? (your answer should be an integer with no units, spaces, commas or even a decimal point)
7.
An attacker is sending packets to the target with the URG flag set in order to scan the target port's status. a. What type of scanning is being performed? b. How will the target port respond if it is open? c. What is the response in the event that the target port is closed?
A series of packets may be sent from one site to another utilising the same route between the two hosts. Please include all of the parts that make up a single packet's end-to-end latency. Will one of the delays last a certain period of time while the other's duration is more erratic?
An IPV4 datagram has arrived with the following information in the header (in hexadecimal): Ox 4 5 00 FFFF 0003 5850 20 06 00FO CB4DAA0C FFFFFFFF i. What is the size of the data? i. Write down the source and destination IP addresses in dotted decimal representation.
The following captured network traffic shows the three-way handshake to establish a TCP connection. Please write a TepDump command running at the client side to capture all the packets with flag "S" only between the host "tclient.net" and the telnet server "telenet.com". When check TCP flags, please use the format 'tep[tcpflags]&tcp-syn', "tep[tepflags]&tcp-push', 'tcp[tcpflags]&tcp-ack', and so on.
In IPsec, each incoming and outgoing packet will be checked with the Security Policy Database (SPD) and the Security Association Database (SAD). (a) What is the checking done with the SPD: (b) What is the checking done with the SAD? (c) Each security association stored in SAD is identified by an integer. What is this integer called?
OSPF messages and ICMP messages are directly encapsulated in an IP datagram. If we intercept an IP datagram, how can we tell whether the payload belongs to OSPF or ICMP?
Please do fast...
1. Please access any web site so you that you can capture TCP packets from an HTTP request. 2. Please expand all the fields in the header of your HTTP request packet. Take a screenshot for all the fields in the header fields of the HTTP packet. 3. Please expand all the fields in the header of the TCP packet in your HTTP request packet. Take a screenshot for all the fields in the header of the TCP packets. Please answer the following questions based on your HTTP request, and TCP packets screenshots: 1. What is the method used in your HTTP request? 2. What is the host name you visited? 3. What is the connection status in your HTTP request? 4. What are the source port and destination port, respectively? 5. What are the sequence number and acknowledgement number, respectively? 6. Which flags are set up in the captured packet? Explain what the flags mean.