When the top of the wheel is tilted outward, then it is called_____ a positive camber b negative camber c•positive caster d negative caster

Q: The crank AB of the mechanism shown on the right is connected to a slider B which moves on the…

A:

Q: Petrol is drained from a tank X to tank Y via pipeline A-B (see figure Q3). A pump is then used to…

A:

Q: For FANUC 6 axis robot How many E-stop buttons does the Fanuc robot system have? Where are they…

A: E-stop buttons are found in various parts of a system. They are designed to be highly visible and…

Q: Determine the location of the sweet spot of the bat shown in the figure (Figure 1). The linear mass…

A:

Q: igure Q6(b) shows a cantilever shaft made of steel subjected to several loading T = 5kNm, M =…

A:

Q: Water enters the bottom of a hot water heater in a home at a velocity of 1.25 ft/s, a temperature of…

A:

Q: Question 4: T shape homogeneous bar m=50 kg mass. Compute the reaction at the pin O just after the…

A: Mass of the T-shape homogeneous bar,

Q: A thin, flat electric heater is exposed to air on both sides. On the top is a heat transfer…

A: To find: The temperature of the heater. Given: The heat transfer coefficient of top is hT=20 W/m2K…

Q: Part A The force F = (-6i+ 3j+ 14 k) N is applied to the block shown in (Eigure 1). Figure -3 m 2 D…

A:

Q: A cylinder of mass m and mass moment of inertia JO rolls without slipping on the ground and is…

A: The cylinder rolls without slipping in the ground.

Q: 1. Crude oil (SG=0.95) flows through a 0.25 m diameter pipe as shown. Given the flow rate and gage…

A:

Q: I need to figure out how to get the Magnitude of the Resultant Force, the elevation angle, and the…

A:

Q: The beam shown is supported at point A by a pin and at location B by a roller. a. Replace the…

A: To determine:a)Resultant force and coupleb)The single resultant force and its distance from A.

Q: t Calculate the three lowest natural frequencies of a solid 20 cm radius steel shaft (G=80* 10'…

A: Given data :- Solid radius = 20 cm Shear modulus = 80 × 10^9 N/m^2 Density = 7500 kg/m^3 Length  =…

Q: Each of the five connected particles has a mass of 0.53 kg, with G as the center of mass of the…

A: The mass of each particle is .The angular momentum of the system is .The x component of velocity is…

Q: A golfer chips the ball into the hole on the fly from the rough at the edge of the green. Letting a…

A:

Q: The two heat exchangers pictured below heat an acetic acid stream by different means. In both…

A: (a) In a heat exchanger, heat is added at constant pressure, therefore, use the formula for heat…

Q: Given TOP VIEW & FRONT VIEW sketch the side view and isometric view Note : Assume each unit as 10 mm

A:

Q: For the compressor shown in the following figure, find the position of the piston with respect to…

A:

Q: A water-drop of 10 μl volume is sliding on an inclined plane surface. This surface is coated with…

A: The Young-Laplace equation, which connects the wetting force to the contact angle and droplet…

Q: 1. Hello can you find Ir1,ir2 ,Ireland, rt and it and pt. Thank you please show me how to do my…

A: Draw the circuit using the directions of currents in each resistors.

Q: FOR A FANUC 6axis robot What button on the teach pendant is used to select a program?

A: What button on the teach pendant is used to select a program?

Q: The figure shows a beam supported by a pivot pin at A and a roller at B. The beam is subjected to a…

A:

Q: Which results in more efficient heat exchange, laminar or turbulent flow?

A: This question is based on the concept of heat exchange.

Q: How many DOF do the following have in their normal environment ? a. submerged submarine b. An…

A: DOF stands for the degree of freedom which indicates the number of values that can be changed…

Q: In (Figure 1), P = 65 lb. The pin at C is attached to member ABCD and passes through the smooth slot…

A:

Q: Example For the position of the mechanism shown in Fig. (a), calculate the angular velocity of the…

A:

Q: e 3 al Views xiliary View 75 TOP VIEW 1₂ 26 26 PLAT SLOTTED SCALE

A: GIven

Q: Sketch the isometric view for the othographic view given below using CATIA V5 ,NO HAND DRAWING

A:

Q: Air at pressure and temperature of 200 kPa, 373.2 K flows through a duct at 270 m/s. The gas…

A: For solution refer below images.

Q: A compound assembly is formed by brazing a brass sleeve on to a solid steel bar of 60mm diameter.…

A: To findFind the diameter of the brass sleeve so that the sleeve carries 20% of the load.Find for the…

Q: Mechanical Draw the part Niew shown ASing object snap moc drawing as P7-1. ave the 04.50 3X 02.00

A: object snap use to get precise location of particular points on object like tangent on circle at…

Q: Write any three terminologies involved in the IC engine

A: Terminologies used in IC engine:- Dead centre Top Dead Centre  Bottom Dead Centre Bore  Stroke…

Q: 1. A full journal bearing of 150 mm diameter supports a load of 40 kN. The speed of the journal is…

A:

Q: Find the force acting in each of the members of the truss shown below. Remember to specify if each…

A:

Q: (b) A bar of 20mm diameter is subjected to a pull of 50kN. The measured extension on guage length of…

A: Given Data The diameter of the bar is:d=20mm The force pull the bar is:F=50kN The change in gauge…

Q: A seamless cover plate for a full face gasketed, flanged joint has been designed. If a material with…

A: Given Data: Pitch circle diameter, d=477 mm Pressure, P=852 kPa

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.