When a specimen of M25 concrete is loaded to a stress level of 12.5 MPa, a strain of 500x10^-6 is recorded. If this load is allowed to stand for a long time, the strain increases to 1000 x 10^-6. In accordance with provisions of IS: 456-2000,considering the long-term effects, the effective modulus of elasticity of the concrete (in MPa) is

When a specimen of M25 concrete is loaded to a stress level of 12.5 MPa, a strain of 500x10^-6 is recorded. If this load is allowed to stand for a long time, the strain increases to 1000 x 10^-6. In accordance with provisions of IS: 456-2000,considering the long-term effects, the effective modulus of elasticity of the concrete (in MPa) is

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

> * The state of two-dimensional stresses acting on a concrete lamina consists of a direct tensile stress o. = 1.5 N/mm² and shear stress T = 1.20 N/mm², when cracking of concrete is just impending. The permissible tensile strength of the concrete is
F 1. The "slump" test is used to determine the compressive strength of a concrete. T 2. For room temperature and axial loading,aluminum behaves as a brittle material. T. F 3. Proper curing is important for a concrete specimen to gain compressive strength. (F) 4. Concrete usually has a good tensile strength. T F 5. The units of the modulus of elasticity are the same as for axial stress. F 6. Plasticity is characterized by return of a material to original size & shape upon removal of stress. T. F 7. Strain hardening increases the elastic strength of the material. F 8. Some materials do not exhibit a well defined yield point. F 9. The failure behavior of our aluminum specimen in our torsion test was expected. T. T F 10. Necking of a steel specimen loaded in tension is an example of Poisson's ratio.
Determine the tensile steel ratio of a singly reinforced concrete beam for the following conditions using concrete strength f’c = 21 MPa and steel yield strength fy = 420 MPa. if the tensile strain is set as 0.009 upon crushing of concrete at a strain of 0.003. = [rr] (5 decimal places)
A concrete cylinder sample has a diameter of 4 inches and a height of 6 inches. The maximum load carried by the sample after its failure is 275 KN. Determine the compressive strength of the sample in psi. (use 1lbf = 4.45 N, round-up your answer to the nearest whole number that is divisible by 5, no need for unit)
A composite column is formed by placing a steel bar, 20 mm in diameter and 200 mm long, inside an alloy cylinder of the same length whose internal and external diameters are 20 mm and 25 mm, respectively. The column is then subjected to an axial load of 50 kN. If E for steel is 200 OOO N/mm’ and E for the alloy is 70 000 N/mm’, calculate the stress in the cylinder and in the bar, the shortening of the column and the strain energy stored in the column.
Estimate the tensile strength required to prevent cracking in a concretelike material that is cast into a bar, 1.25 m long, and is fully restrained ateach end against axial movement. The concrete is initially cast and curedat a temperature of 40°C and subsequently cools to a temperature of –20°C.Assume that the modulus of elasticity is 35 GPa and the thermal coefficient is9 X 10-6m/m/°C.
Please include photos of the tables you used.
Q-2(a) When a specimen of M25 concrete is loaded to a stress level of 12.5 MPa, a strain of 500 × 10-6 is recorded. If this load is allowed to stand for a long time, the strain increases to 1000 × 10-6. In accordance with the provisions of IS:456-2000, considering the long-term effects, the effective modulus of elasticity of the concrete (in MPa) is ______
A metal specimen with 20 mm diameter and 100 mm gauge length is loadedelastically with 5 kN and elongates 0.8 mm. Its diameter under this load is 19.95 mm. Calculate:a) the Bulk Modulus, Kb) the Shear Modulus, G
A compact tension specimen is tested according to ASTM standard E399. The load displacement curve is shown in the Figure below with PQ= 120 kN (Type 1 curve). The specimen dimensions are B=0.5 cm, W=10 cm, and “a” =5 cm. If the materials yield stress is 600 MPa are the conditions correct for a valid K1C measurement? Please look up McEviley’s textbook on the thickness criterion for a valid fracture toughness value.
1. For the concrete beam shown, calculate the maximum tensile force (P) that can be applied to the beam before failure. The fracture toughness of concrete is 0.23 MPa(m)0.5, its elastic modulus is 25000 MPa, and the maximum flaw size (middle flaw) is estimated as 4mm inside concrete. Assume fgeom = 1, SF=1, and yield/tensile strength to be 3MPa. 2. A material possesses a fracture toughness of 48 MPa?m?. Determine the critical size (length) of the crack if is subjected to a critical far field stress of 1460 MPa. Assume infinite geometry and include a drawing. 5cm 15cm 50cm
The development length in compression for a 20 mm diameter deformed bar of grade Fe415 embedded in concrete of grade M25 whose design bond stress is 1.40 N/mm² is-