When a bar with the hexagonal cross sectionshown in Fig. (a) is subjected to a torque T,numerical analysis shows that the maximumshear stress in the bar is Tmax =5.7T|3.Determine the percentage loss in strength thatresults when a circular bar of diameter dismachined into the hexagonal shape shown inFig. (b).Location of Tmax-(a)(b)FIG. P3.53

Answered: Image /qna-images/answer/7732d049-1f07-44c5-936b-3e460519f8d7.jpg

When a bar with the hexagonal cross section shown in Fig. (a) is subjected to a torque T, numerical analysis shows that the maximum shear stress in the bar is Tmax = 5.7 T/. Determine the percentage loss in strength that results when a circular bar of diameter dis machined into the hexagonal shape shown in Fig. (b).

When a bar with the hexagonal cross section shown in Fig. (a) is subjected to a torque T, numerical analysis shows that the maximum shear stress in the bar is Tmax = 5.7 T/. Determine the percentage loss in strength that results when a circular bar of diameter dis machined into the hexagonal shape shown in Fig. (b).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Figure shows that a hole must be drilled in a plate with a shear strength of 40 ksi. Compressive stress in the punch is limited to 50 ksi. calculate the thickness maximum of the plate in which a hole of 2.5 inches in diameter can be drilled. The figure is in the attached image.
Q8
(30%) A circular aluminum tube subjected to T pure torsion by torques T has an outer radius r2 equal to 2 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 500x10-6 rad, what is the shear strain y1 at the inner surface? (b) If the maximum allowable rate of twist (0) is 0.15°/m and the maximum shear strain is to be kept at 500x10-6 rad by adjusting the torque T, what is the minimum required outer radius (r2 )min?
8.8 (A/B). Opposing axial torques are applied at the ends of a straight bar ABCD. Each of the parts AB, BC and CD is 500 mm long and has a hollow circular cross-section, the inside and outside diameters being, respectively, AB 25 mm and 60 mm, BC 25 mm and 70 mm, CD 40 mm and 70 mm. The modulus of rigidity of the material is 80 GN/m³ throughout. Calculate: (a) the maximum torque which can be applied if the maximum shear stress is not to exceed 75 MN/m²; (b) the maximum torque if the twist of D relative to A is not to exceed 2. [E.I.E.] [3.085 kNm, 3.25 kNm]
Asap please
Why did it became 4F/A from F/A, in (a)
A rod specimen of ductile cast iron was tested in a torsion-testing machine. The rod diameter was 30 mm, and the rod length was 300 mm. When the applied torque reached 260.8 N·m, a shear strain of 1605 microradians was measured in the specimen. What was the angle of twist in the specimen?
A square key fixing a gear on a 30 mm diameter shaft. The shaft is transmitting a power of 18 kW to the gear at 800 rpm. The key is made of steel with a yield strength of 470 N/mm² and the factor of safety is 2.5. The yield strength of the key material in compression can be assumed to be equal to the yield strength in tension. Determine the dimensions of the key.
Please present drawings/FBD’s illustrating your solution.
Steel shaft can be produced as solid body or circular tube with circular tube. The shaft must bear a torque of 1200 Nm. Since the shear strength for the shaft material is 40 MPa, the maximum allowable unit torsion angle of the bar is 0.75 ^ 0 / m and the shear modulus of steel is G = 78 GPa;a) Find the required diameter d0 for a solid circle shaft.b) Find the required outside diameter d2 for a ring-section shaft whose thickness is one tenth of the outer diameter.c) Find the diameter ratio (d2 / d0 ratio) and weight ratio for ring cross section and solid section shafts
C G (5 esc ± § A9 cm diameter solid aluminum post is subjected to a horizontal force of V=8.5 kN and a concentrated torque of T=8.8 kNm, acting in the directions shown in the figure below. Assume that L= 0.5 m. The yield strength of the aluminum is oy = 250 MPa. Determine at point K: a) Normal stress due to bending caused by V. Enter your answer in MPa to 2 decimal places. Answer: 1 Check Question 2 Not complete Q @ 2 € W £ 3 # E S4 $ R % 5 T 6 Y & 7 U * 8 1 ( 9 O ) 0 P + [ ]