3) A cantilevered bar has a circular cross section with 15-mm diameter and shear modulus of G = 26 GPa subject to a torque of T = 10 N-m at the free end. (a) Calculate the magnitude of the maximum shear stress and (b) the angle of twist of the end of the bar in degrees.

Q: Which of the following statement is correct Select one: Friction causes objects to slip down…

A: Friction force is directly proportional to the normal force acting to body and independent of area…

Q: Which among the following is a forming process in which thickness of the metal plate is decreased by…

A: Rolling: In this handle, the workpiece within the frame of slab or plate is compressed between two…

Q: If the analysis of the forces involved on an object produces a negative answer for a force: The…

A: If doing calculation and getting any force hwith negative that means, The negative sign indicates…

Q: Which among the following is a forming process in which thickness of the metal plate is decreased by…

A: Metal forming processes are the processes in which plastic deformation of the material is done in…

Q: Impact velocity equation

A:

Q: Give an example of concentrated force.

A: Whenever total magnitude of a force act on a single point then this type of loading on a beam is…

Q: 2. Sharp notches are often added to plastic food packages to help open them (along with arrows…

A: Detailed explanation:Sharp notches are a very good example of the functional features to the plastic…

Q: The following is a schematic diagram of the Charpy impact tester. Is from the following. At this…

A:

Q: What is speed?

A: Speed is a scalar quantity that can give us information about the rate of an object or a body…

Q: 3

A: intro- defects on any material is cause of failure of material.

Q: Need auxiliary views of this drawing

A: This question is based on the concept of engineering drawing.

Q: To show how individual pieces fit together, it is necessary to use larger-scale drawings and section…

A:

Q: 1.Forging is a process that uses application of force to give shape to metal.

A: Forging is a process that uses application of force to give shape to metal. Answer: True

Q: What is the maximum thickness dimension allowed on the part?

A:

Q: If the part was cut by this plane, what would the resulting remaining face look like?

A: Section planes in SketchUp cut a model along a plane so you may look within it without altering…

Q: Compare the bolt patterns in shear shown below. The distance from the load to the centroid is the…

A: following is the answer and explanation for the above question-

Q: On a technical drawing, what is the difference in the application of the "cutting plane line" and…

A:

Q: Files are used for removing large of amount of materials. Select one: True False

A:

Q: What does shear strains cause?

A: Answer Shear Strain : it is the angular displacement from the original position

Q: ACTIVITY 6: LINE TYPES ft. a Simple Object Dimension line (Thin) 8 cm Extension line 5 mm THK (Thin)

A: Defined the types of lines as follows. Center Lines Extension Lines Dimension Lines Cutting Plane…

Q: In drawing process, tensile forces are used to reduce the cross section of the workpiece. Select…

A: The drawing process is generally is done at the room temperature. To reduce the required forces, it…

Q: FRONT VIEW

A: According to the details provided in the question, we need to calculate ISOMETRIC VIEW

Q: 1- What type of drawing is this (Assembly, detail assembly, detail, pictorial)? And What is the…

A: We are authorized to answer three subparts at a time since you have not mentioned which part you are…

Q: In a hydraulic press machine the diameters of the effort and load pistons are respectively 25 cm and…

A:

Q: What is external force?

A: Answer : Force - It is an effect which changes or try to change the state of a body.

Q: y

A:

Q: A solid cylinder is rolling down a ramp that is rough enough to cause the cylinder to roll without…

A: This question is solved with the help of the law of conservation of energy. Under pure rolling,  The…

Q: What is the key information that needs to be incuded in a section view on an assembly drawing.…

A: The Answer is below

Q: What type of lines can be used in a drawing to show that part of an object has been removed ?

A: Solution : There are two types of line which are used to show the removed part of an object : Break…

Q: You can use a lever to increase force, distance, and speed.  True or false?   (simple machines:…

A: You can use a Class 1 or Class 3 lever to increase the speed of the load, according to where the…

Q: Rolling friction occurs when one surface slides over another surface  Select one: True False

A: Rolling friction is seen between the two surfaces which are in rolling.contact

Q: The possibility to make the required shape from the material is considered during the criteria for…

A: Material to make the desired shape is considered during the criteria of selection. Because during…

Q: 1. Given that the length of the sample is 90 mm and the diameter of it is 7 mm. i. Draw the stress…

A: Write the expression of stress. Write the expression of strain. Draw the given table and calculate…

Q: This statement is true or false? Process of making raw material to a final desired product is called…

A: Given Data : Raw Material Final desired product

Q: Center of gravity of a plane area. Shear force. Point of contraflexure.

A: Centre of gravity of a plane area: The centre of gravity of a plane area is a point inside or…

Q: Isometric View Top View Front View Right Side Section View

A: Given: Front view is assumed to in the direction shown below,

Q: What kind of information does a detail view on a drawing provide

A: A detailed drawing can be drawing of an object, assembly of multiple parts, or an entire system of…

Q: Negative force and Displacement will cause compression andcontraction? True or False?

A: The negative force causes compression is a true statement. In the end, the resultant forces must be…

Q: A six inch diameter cylinder with a two inch rod pushes out its full stroke of 20 inches in 1.5…

A: Forward stroke Area : π462-22=25.13 in2 Volume : V=A×L=502.65 in3 Flow rate : Q=Vt=335.1 in3/s…

Q: What is the max circularity, on a radius, on the part below before a feature control frame is…

A: The tolerance of the part is

Q: In wire drawing process, the cross sectional area of wire is reduced. Select one: True False

A: In wire drawing, Material is extruded .

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.