When a 0.01 M KCl solution was filled into a conductivity cell at 25°C and its resistance was measured, 150.00 ohms was found. The intrinsic conductivity of a 0.01 M KCl solution at 25°C is x = 0.0014088 ohm-1.cm-1. In the same cell, the resistances of saline solutions of various normality are measured in the same way: Calculate a) the cell constant and b) the conductivity of the hydrochloric acid solutions. - Normality of Salt Acid 0,1 0,01 0,001 0,0001 Resistivity of Salt Acid 390 1124 9967 90850

When a 0.01 M KCl solution was filled into a conductivity cell at 25°C and its resistance was measured, 150.00 ohms was found. The intrinsic conductivity of a 0.01 M KCl solution at 25°C is x = 0.0014088 ohm-1.cm-1. In the same cell, the resistances of saline solutions of various normality are measured in the same way: Calculate a) the cell constant and b) the conductivity of the hydrochloric acid solutions. - Normality of Salt Acid 0,1 0,01 0,001 0,0001 Resistivity of Salt Acid 390 1124 9967 90850

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

Part c
Drowser Time Limit: 0:20:00 Time Left:0:15:19 Glenton Morris: Attempt 1 160 40 3.0 Page 1: 140 - 35 3.0 120 10 25 100 2.0 80 60 Z 10 Page 2: 05- 20 0 2. Time is 10 Timetsk 10 Page 3: Of all the graphs shown above, what plot type is correctly represented? O second order Page 4: O no plot shown is valid 4. 1st order 3rd order OL X (W) FON
Question 1 of 20 A barrel of crude oil has a volume of 42 gallons, only approximately 45% of which is processed into gasoline. If your car achieves 32 mi/gal, and you drive 36,000 miles in one year, how many barrels of crude oil are required to run your car for a year? Tap here or pull up for additional resources
Please step by step solutions
When pure sulfuric acid is dissolved in water, heat is evolved. 10.65 g of pure sulfuric acid at 20.00 °C was added to a calorimeter containing 300 g of water at 20.00 °C. The temperature of the solution increased to 26.35 °C. If the specific heat of the mixture is 4.184 Jg1°C1, the density of water is 1 g/mL, and the heat capacity of the calorimeter is ignored, what is the heat evolved per mole of sulfuric acid? a. -83.2 kJ O b. -73.6 kJ O C. -76.0 kJ d. -80.8 kJ e. -78.4 kJ
1 1/2 yr to months using dimensional analysis
A student determined that the mass of four pennies was 8.7 grams. Use this information to calculate the number of pennies in a box that contains 2.5 pounds of pennies. Rouund your answer to the nearest whole number. For the toolbar, press ALT+F10 (PC) or ALT+FN+F10 (Mac).
Plz answer correctly in 20 minutes plz it's very urgent
Below is a simple set of weights obtained while immersing potato slices in various sugar solutions over 30 minutes. I need help calculating all of this for a 30 min period a. For each solution, calculate the rate of weight change over this 30-minute period. Show your work in the space below. Once you calculate these rates - fill in the blanks below and then add these answers to your Canvas exam. Write your answer in standard notation and use 3 digits past the decimal point - e.g. 0.005, 0.030. (Note that the last zero in an answer is considered to be a digit). Show your work in the space below. 0.0 M sucrose = _______ _____________ g/min 0.4 M sucrose = _______ ____________ g/min 0.6 M sucrose = ________ ____________ g/min 0.8 M sucrose = ____________________ g/min 1.0 M sucrose = ________ __________ g/min Using the osmosis data in the question above, determine the percent weight change for each sucrose solution and fill in the blanks given below and then add these answers to…
Answer question number 7 on the attached document
Home Insert Draw View A Text Mode Lasso Select Insert Space + 4. When measuring the volume of a liquid, how would sample size (e.g., using a 10 mL graduated cylinder vs. a 100 mL graduated cylinder to measure out 70 mL of a liquid) affect the absolute error and percentage error in the measured values of mass and volume and therefore the density?
Answerr part b