What will happen to the critical Reynolds number for each of the following cases and why: i- Pressure gradient is made more adverse. ii- Surface roughness is decreased. iii- Free-stream turbulence is increased. iiii- Pressure gradient is made more favorable. iiiii- Surface roughness is increase. iiiiii- Free-stream turbulence is reduse.

Q: A hydrostatic bearing is to support a load of 1000 Ibf/ft of length perpendicular to the diagram.…

A:

Q: 7.11. If the turbulent velocity profile in a pipe 0.6 m in diameter may be approximated by v = 3.56…

A:

Q: In an experimental set-up to measure the shock losses due to sudden expansion, the following…

A:

Q: Diameter 60 mm, length-to-diameter ratio 1, bearing clearance 0.12 mm and radial load carried ISO…

A: D=60 mmc=.12 mmW=8000 NN=1440 rpmT=40°C

Q: Explain the physical meaning of Reynolds number and Froude number

A:

Q: (Q)A pump running at 1,440 rpm has to support a load of 10 kN. Journal diameter is 130 mm. Design a…

A:

Q: A student team designed an electric car to participate in a race. The overall length of the car is…

A:

Q: If a body with a linear dimension of 1 ft is moving in a fluid with velocity q, find the Froude…

A: Feel free to ask any doubt. I hope it is helpful.

Q: A 500-mm diameter welded steel pipe (e = 0.046 mm) conveys 20°C crude oil (density = 856 kg/m and…

A:

Q: A shaft 70.0 mm in diameter is being pushed at speed of 0.4 m/s through a bearing sleeve 70.2 mm in…

A:

Q: The figure shows a duct in which methyl alcohol at 25°C (density ρ= 789 kg/m3, dynamic viscosity μ =…

A: Given data, Density of methyl alcohol, ρm=789 kg/m3 Dynamic viscosity, μ=5.6×10-4 kg/ms Volume flow…

Q: For flowing water at 10°C, what is the magnitude of the velocity gradient needed to produce a shear…

A:

Q: A fluid with viscosity of u = 1.752 x 10-5kg/m. s and density of p= 1.2kg/m³ %3D flows at U=1 m/s…

A: We have to determine (a) Find the boundary layer thickness at the end of the plate. (b) Find the…

Q: 1) For a parallel laminar flow over flat plates, the friction coefficient depends only on the…

A: Solution:

Q: Maximum thickness of thermal boundary layer formed when the fluid is flowing through the pipe of…

A:

Q: Water at 20 deg C flows between two parallel horizontal plates separated by a distance of 8 mm. The…

A: Write the given data. T=20 °Ch=8 mm=0.008 mv=4 m/sτupper=0

Q: 1.A.)A cylindrical shaft of radius 5 cm is rotating at a speed of 50 rad/s in a cylindrical bearing…

A:

Q: If the size of uniform sand-grain roughness in a 10 in. or 254 mm pipe is 0.02 in. or 0.5 mm, below…

A: Given: d = 10 in e = 0.02 in To find: below what Reynolds number will the pipe behave as a…

Q: Assuming a linear velocity distribution in the oil film find the terminal velocity (m/s) of the…

A: Given,  Mass of the block , m =12.3 Kg Area , A = 35 cm2 Thickness of the oil film , t =1 mm…

Q: A group of students is designing a small, round (axisymmetric), low-speed wind tunnel for their…

A: Given, uz,L = 120 ft/s D0 = 5 ft DL = 1.5 ft L = 3 ft At standard temperature and pressure velocity…

Q: D Page view Read aloud T Add text V Dray 6. An oil with density of 900 kg/m³ and kinematic viscosity…

A:

Q: In turbulent flow, greater mixing and shearing occur. (True or False)

A: Reynolds number: The ratio of inertia force to the viscus force is called Reynolds number. The value…

Q: (a) The gap between two horizontal plates is 5 mm. The gap is filled with oil of a relative density…

A:

Q: Calculate the Reynolds numbers at the root chord location for the following aircraft. Assume that…

A:

Q: What does the shear flow measure?

A: The shear flow is defined as the shear force per unit length in a thin walled perimeter. The…

Q: 171 about industrial piping HOW IS THE HYDROSTATIC TEST PRESSURE DEFINED IN INDUSTRIAL PIPELINES?

A: The objective of the question is to understand the definition and calculation of hydrostatic test…

Q: Local shear stress for flow over a surface is given by the following equation; Using this relation,…

A:

Q: A lattice of vanes positioned upwind to the measuring station of an air tunnel consists of flat…

A:

Q: . Two reservoirs containing water (density of 1.94 slug/ft³ and molecular viscosity of 2.09 x 10-5…

A: The diameter of pipe 1 is d1=1 in.The length of pipe 1 is l1=20 ft.The diameter of pipe 2 is d2=2…

Q: A circular plate with a diameter of 2m and weighing 350N slides down an inclined plane with a…

A:

Q: transition region for a laminar flow usually takes place at   a. near trailing edge B. lower…

A: Handwriting.jpg

Q: The airplane is flying at an altitude of 6500m with a speed of 220m/s. Determine the critical…

A: To find: The critical velocity and critical pressure coefficient. Given: The altitude of the plane…

Q: What is the mean kinetic energy of the turbulent velocity fluctuations, if u¹²=0.2, u¹2=0.08,…

A: Given data:- u1'= 0.2, u2'=0.08, u3'=0.2. To find:-the mean kinetic energy of the turbulent velocity…

Q: Provide an example list of Laminar and Turbulent Flow.

A: ● Laminar flow is a smooth flow which flows without any interference or intermixing of fluid layers…

Q: When a uniform stream flows past an immersed thick cylinder, a broad low- velocity wake is created…

A: The width is .

Q: Present and validate how Stokes Law is used to analysing fluid behaviour and measure the viscosity…

A: A fluid's viscosity is a measure of its resistance to deformation at a particular rate. A fluid…