a band moves at a speed V and is in contact with a surface of an oil tank with viscosity m. calculate the power in watts required if the belt is moving at 2.9 m / s over SAW 30W oil at 20 C with L = 2m, b = 60m, Nu = 329.0mm ^ 2 / s, rho = 0.9g / cm ^ 2 and h=3cm

Q: C1 (a). A lubricating oil having the dynamic viscosity of 0.058 poise and specific gravity of 1.11.…

A:

Q: A vertical gap 2.2 cm wide of infinite extent contains a fluid of viscosity 2.0 N s/m? and specific…

A:

Q: A lubricating oil having the dynamic viscosity of 0.055 poise and kinematic viscosity of 0.17…

A:

Q: Calculate the power required per meter of width of stream to force lubricating oil through the gap…

A:

Q: The apparatus shown in the figure is to coat a thin steel plate with oil. using for. Fluid1 has a…

A:

Q: One end of a capillary tube 10 cm in length and 1 mm in diameter is connected to a water supply…

A:

Q: The belt moves at a steady velocity V and skims the op of oil tank. Assuming a linear velocity…

A:

Q: A hydrodynamic journal bearing is subject to 2000 N load at a rotational speed of 2000 rpm Both…

A:

Q: Figure 1 shows a layer of oil(8.95 kN/m^3),

A:

Q: C1 (a). A lubricating oil having the dynamic viscosity of 0.058 poise and kinematic viscosity of…

A: C1 (a): Given data: Dynamic viscosity of lubricating oil, μ=0.058 poise and it's kinematic viscosity…

Q: pllllzzzz help me right nowww plzzz  The belt moves at a steady velocity V and skims the top of oil…

A: Given data: V= 3.5 m/s L= 2 m b = 60 cm h = 3 cm Need to determine the required belt-drive power.

Q: An 18-kg slab slides down a 15° inclined plane on a 3-mm-thick film of oil with viscosity of…

A:

Q: You are working in a machine tool manufacturing industry for the project to design CNC control…

A:

Q: Two indefinitely long flat plates separated by 3 inches in distance but with a thickness of 5 inches…

A: As per the our guideline we are supposed to solve only one question per post. kindly repost other…

Q: A plate 0.05mm distant from a fixed plate moves at 1.15 m/s and required a force per unit area of…

A: As per the Bartleby rule, We’ll answer the first question since the exact one wasn’t specified.…

Q: The belt moves at a steady velocity V and skims the top of oil tank. Assuming a linear velocity…

A:

Q: Dm = a shaft with a diameter of 75mm Dy = 75.150mm in diameter and L = Its viscosity is 0.15 kg /…

A:

Q: A fluid is being pumped through a pipe. The density of fluid is 872 kg/m³. The viscosity is 2.8x10²…

A: Given data: The density of the fluid is = 872 kg/m3 The viscosity of the fluid is = 2.8 x 10-2…

Q: A square metal plate 1.5 m side and 1.5 mm thick weighing 50 N is to be lifted through a vertical…

A:

Q: Calculate the electrical power input to an electric motor (nm = 95%) to drive the pump (np = 85%).…

A: The overall efficiency is:

Q: 6. A hydraulic lift (see below) of the type commonly used for greasing automobiles consists of a…

A: Introduction: A hydraulic lift is used to lift the object by using the force created when the…

Q: A hydraulic lift of the type commonly used for greasing automobile consists of a 280.18-mm- diameter…

A:

Q: A piston having a diameter 0.15 m and a length of 0.25 m as shown in figure (1.2) slides downward…

A:

Q: 1 (a) A plate 0.05mm distant from a fixed plate moves at 1.15 m/s and required a force per unit area…

A:

Q: The belt moves at a steady velocity V and skims the top of oil tank. Assuming a linear velocity…

A:

Q: Q1/ A 120 mm disc rotates on a table separated by an oil film of 1.8 mm thickness. Find the…

A: As per the guidelines of BARTLEBY we are subjected to solve only one question at a time. Please…

Q: Q1/ A 120 mm disc rotates on a table separated by an oil film of 1.8 mm thickness. Find the…

A:

Q: 6. A hydraulic lift (see below) of the type commonly used for greasing automobil 280.00 mm diameter…

A: Given data as per questionDiameter of ram, d=280 mmDiameter of cylinder, D=280.18 mmOil film…

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.