What site development components are shown on a site plan?

Q: The soil profile from a geological map of a project site obtained during a Phase 1 investigation as…

A: Geo technical engineering is the study of how soils respond to loading forces and interactions…

Q: What are the advantages and limitations of mechanical excavation techniques compared to manual…

A: Excavation is a process of digging or removing the soil and when it done using machines it is called…

Q: What is Dynamic Deep Compaction/Consolidation?

A: Dynamic deep compaction:

Q: Please round to the nearest One (i.e., 1). PLEASE DO NOT USE COMMA(S) ON YOUR ANSWER!!! A proposed…

A: For embankment V= 7500ft3e=0.6e=VVVS0.6=V-VSVS0.6=7500-VSVSVolume of solids required Vs=5554.66ft3

Q: How are subsurface conditions on a site determined?

A: Answer Subsurface is the layer below the surface we find the condition before make the flooring.

Q: You've been tasked with deriving a site-specific shrinkage factor for earthwork planning on your…

A: Size of pit = 10 ft x 6ft x 3 ft Mass of soil excavated = 10.25 tons

Q: 3- Using the Grid method, determine the cuts and fill for the project shown in the figure. The grids…

A: Grid Method The grid method for cut and fill volume is a technique used to calculate the amount of…

Q: Why is it important for an estimator to be knowledgeable of the OSHA requirements regarding…

A: Solution:  An estimator must be knowledgeable of OSHA's safety rules and regulations for excavations…

Q: year Q3/Complete the earthwork calculation sheet and plot the resulting mass diagram. Assuming…

A: Plotting the Mass DiagramTo plot the mass diagram:1. Use the stations as the x-axis.2. Use the…

Q: At a project site, the soils must be identified and characterized through a soils investigation.…

A: a) An oversimplified site investigation might seem like a cost-saving measure at first glance, but…

Q: Explain the following terms or statements: (i) The requirements for bedrock for a large diameter…

A: In this question two various question is being asked regarding geo technical engineering

Q: 4. Determine the volume of excavation from the area shown on the layout below. Each elevation point…

A:

Q: A 12” water main is being installed along the shoulder of a rural road. The excavation for the water…

A:

Q: In reply to figure-4.15-site-plan-for-review-question-11 I calculated the answer as cubic feet and…

A: Conversion of units refers to the process of changing the units of a physical quantity from one…

Q: Prepare a bare cost estimate based on national average prices for the following storm drain…

A: Trench size =350 ft ×4 ft × 5 ft Pipe diameter = 18 in Swell factor = 22% Shrinkage factor = 15%…

Q: Explain about obtaining samples of soil groundwater and soil gas relate to diagnosing and monitoring…

A: Soil contamination or soil pollution is generally caused by the presence of chemicals (which are not…

Q: The soil profile from a geological map of a project site obtained during a Phase I investigation is…

A: Steps: 1. Making plans for a soil exploration campaign.2. Taking soil or rock samples from the…

Q: Solution: 8,412.00 m² Site Details: Section Width (S)-12 m 13 m 49 m 51 m 58 m 60 m 60 m 57 m…

A: Step 1: Analyzing the Excavation Site Understanding the Data:The excavation site is divided into…

Measuring site work, Excavation and Piling

Bid drawings typically include very little material about the precise requirements of site work operations, measuring site work and excavation work differs from measuring most other works on a construction project. The actual site work conditions are not provided and also the dimensions of the excavations are not known during the pre-construction phase. The precise measurement of the excavation and backfill of the earth material and topsoil is important for a contractor to decide upon the total cost required for the process. All the works should be carried out under OSHA (Occupational Safety and Health Administration) standards to ensure the safety of the workers.