What should be the size of the base (footprint) of a square footing if it supports a column with a service dead load of 200 kips and a service live load of 160 kips. The base of the footing is 5 ft below grade, and the soil unit weight is 110 lb/ft. The allowable soil pressure is 5000 psf. (

What should be the size of the base (footprint) of a square footing if it supports a column with a service dead load of 200 kips and a service live load of 160 kips. The base of the footing is 5 ft below grade, and the soil unit weight is 110 lb/ft. The allowable soil pressure is 5000 psf. (

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A rectangular footing, with a plan area of 1-4mx2·0m is to be placed 2m below the ground surface.…

A: Given Information:

Q: Design round column footing for 18 in diameter that supports loads of PD = 240 k and PL = 140 k. The…

A: Answer ACI code states that the round column or regular polygon shaped column may be replaced with…

Q: Question 2: For the footing given below, calculate the ultimate bearing capacity (qu or qf) and net…

A: Given:- The depth of the foundation = Df = 3 m The dimension of the footing = 6 m × 6 m The value…

Q: = A proposed building is to be supported on a series of spread footing embedded 36 inches into the…

A: d= 36 inch Cc1+e0=0.12Cr1+e0=0.03s'm= 5000 lb/ft2g=120 lb/ft3GWT= 15 ft below the ground surfaceS=1…

Q: Assuming general shear failure and using equation 6.28 with a FOS of 3 find the allowable gross…

A: Asked: To determine the allowable gross load for the given strip footing. Given: Width of the…

Q: What equations did you use to solve for the shape factor for circular and square footing?

A: The Meyerhof's bearing capacity equation is given by ;The above equation ;Fcs , Fqs and are the…

Q: 3. Calculate the total load on a 4'x4'x1' spread footing that is buried 3' below, and a hot tub is…

Q: N. N, N. N. Ni, 5.70 1.00 0.00 26 15.53 6.05 2.59 1.07 0.005 16.30 2.88 5.90 6.10 27 28 6.54 1.14…

Q: a square footing is to be constructed on a uniform thick deposit of clay with a unconfined…

Q: footing is loaded as shown in figure 2. Compute contact pressure and soil pressure diagram.

Q: An existing building is to be renovated. One of the existing footings is 1.5 m by 1.5 m in area and…

A: Given data: Load on the footing = 2000 kN Size of the footing = (1.5 x 1.5) m Angle of internal…

Q: Define the ultimate bearing capacity equation for the general shear failure of soil in Terzaghi's…

A: Ultimate bearing capacity : The ultimate bearing capacity of a foundation denotes the maximum load…

Q: Refer to the footing detail shown below. The net allowable soil pressure is 6000 psf (qe). Assuming…

A: We know that Net allowable soil pressure is given by qe = Service load/footing area Service load =…

Q: An interior column for a manufacturing building will be supported on the site’s natural clay soil,…

A: The ultimate bearing capacity for square footing is given by,

Q: Submit the following online or on paper: The footing below is a 5ft square. The soil immediately…

A: The unit weight of the soil above the footing, The unit weight of the soil below the footing, The…

Q: Assuming general shear failure and using the Terzaghi equation with a FOS of 4 find the allowable…

A: Given width of footing,B=3 ft Factor of safety=4 depth of footing,Df=3 ft angle of friction,φ=28°…

Q: Calculate the amount of soil that need to be excavated for wall footing that has a depth of (h).…

A: Que:- Calculate the amount of soil that needs to be excavated for wall footing that has a depth of…

Q: 50'-0" 25'-0" C. 2'-6" Footing cross section -6 a. THREE DIMENSIONS: If this slab has a continuous…

Q: In order to minimize the stress induced in the soil, a larger footing area should be employed.…

A: Given data in question Footing area Stress induced To find out True or false

Q: a continuous footing installed at a depth of 2 feet with a base of 5 feet wide is constructed on the…

A: Df = 2 ft B = 5 ft γ = 120 pcf ϕ' = 35o

Q: A certain column carries a vertical downward load of 448.0 k. It is to be supported on a 3.0-ft deep…

Q: Explain the procedure developed by Hunt (1986) for determining allowable bearing pressure of…

A: Bearing Pressure : The bearing capacity of soil is the maximum average contact pressure between the…

Q: A 4ft by 4ft spread footing is proposed where the bottom of footing is set 2ft below grade. The…

A: Question is based on the footing which is proposed to design a which bottom of which is set at some…

Q: A rectangular combined footing 8 ft * 20 ft is founded at a depth of 6 ft on a normally…

A: B = 8ft. D = 20ft. B' = 6ft Zh = 28 ft. qc = 50tsf

Q: A proposed office building will include a 10 ft x10 ft square, 3 ft deep (the footing height is also…

A: Given, Cross sectional area of footing = 10 ft x 10 ft Depth of footing = 3 ft Angle of internal…

Q: The allowable soil bearing pressure at a building site is 5,500 psf. Determine the plan dimensions…

A: To find the plan dimensions of the footing. Given Data load F = 430 kips = 430 x 1000 lbs Allowable…

Q: A rectangular footing 13'x14' supports a rectangular column 12" x 24", with DL = 340 kips and LL =…

A: To determine the total soil pressure and check if the footing size is appropriate. Given, Size of…

Q: 10. Calculate the ultimate bearing capacity considering the following: A. A strip footing, 2 meters…

Q: Please complete the structural design of a rectangular footing with B = 0.92 m and L = 1.22 m. The…

A: Design procedure for rectangular footing: Finding the size of footing. Net upward pressure.…

Q: The thickness and reinforcement of a spread footing are governed by structuralconcerns. Structural…

A: LRFD Method: LRFD stands for Load and Resistance Factor Design, which is implemented by Limit State…

Q: A square footing (10' x 10') is located 6' below grade. The lowest corrected N value (blow count) is…

A: The values given in the question are as follows: Width of square footing(B)=10 ft Depth of…

Q: a square footing with a size of 10 ft by 10 ft is located 8ft below the ground surface. the subsoil…

Q: A circular footing has a radius of 4 ft. An engineering is looking for the stress in the soil 20 ft…

Q: Compute the elastic settlement for a rigid 10 ft by 15 ft footing loaded with 4000 psf uniformly…

Q: A 7 foot-square footing is embedded 3 feet below the ground surface and is supported on a clayey…

A: Given:- The dimension of the square footing = 7 ft The depth of footing below the ground surface = 3…

Q: PLEASE ANSWER IT ALL ASAP FOR AN UPVOTE. THANKYOU. A 0.9 meter radius circular footing is embedded…

Q: Which footing will support the highest proportion of the load (critical footing)? (LO2) 3 1. A B C…

Q: Determine the maximum allowable service axial load (dead+live) that the isolated spread footing…

A: Given Data:Footing dimension= 1.50m sq.Footing thickness= 0.75mColumn size and orientation : 250mm…

Q: (2) What is the efect of the new footing on the old footing? Suggest a method to minimize these…

A: The effect of new footing on the old footing. As from the picture, if natural ground level for old…

Q: Determine the increase in vertical stress directly below the center of the footing

A: Load (q) = 14506 lbs/ftwidth of footing = 2.3 ftdepth of footing (z) = 0.8 ftNeed to findThe…

Q: Soil Mechanics Problem: A footing with dimensions of 8ft x 12ft constructed at the surface of the…

Q: - Given: A "shovel" footing that is 8" deep and 8" wide on the bottom with sides that slope out at a…

A: Schematic representation of the given problem:

Q: Question 3. A strip footing is to be used in a clay soil in which the imposed load is 1 MN/m length.…

A: Cohesion , Angle of Internal friction , Unit weight ,

Q: A proposed office building will include a 10 ft x10 ft square, 3 ft deep (the footing height is also…

A: To calculate the maximum bending moment from an earthquake that this foundation can support, you…

Q: (5) There is a strip footing with a width of 2 m and a buried depth of 1.5 m. The foundation soil is…

A: The Ultimate Bearing capacity is calculated by Terzaghi theory.

Q: 7. A continuous strip footing bears on sand with groundwater one-half the footing width below the…

A: Given Strip continous footingWater table depthDepth of footing To find out Choose the correct…

Q: A 5 * 7 ft footing is founded at a depth of 2 ft and supports a vertical load of 80 k and a moment…

A: Solution Given Data Foundation Dimension= 5*7 ft Vertical load= 80 k Moment load in the B Direction=…

Q: structural engineer wants to consider placing the base of the building so deep that the soil below…

A: Weight of buliding = 10790 kipsSize of buliding = 65×65 ftCohesion = 418 psfWeight of soil = 118 psf…

Concept explainers

Electronic Spreadsheet

Tabular listing has many advantages ranging from time management to efficient scheduling of tasks. Electronic spreadsheets allow the user to tabulate and analyze data, using its easy-to-use interface. An electronic spreadsheet is a staple application used among accountants, management staff, and IT professionals. It is used in various sectors worldwide for data management. An electronic spreadsheet is a system and computer software that could be used to do numerical computations automatically. Spreadsheet application programs are often organized as a table with rows and columns. Each row and column intersect to form a cell, which may be used to store data. These data can take the form of a written label, a number, or a formula that combines information from other cells.

Question

What should be the size of the base (footprint) of a square footing if it supports a
column with a service dead load of 200 kips and a service live load of 160 kips. The
base of the footing is 5 ft below grade, and the soil unit weight is 110 lb/ft. The
allowable soil pressure is 5000 psf. (

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A proposed building column will carry a maximum downward unfactored load combination is 250 kips and a service load of 185 kips. The column is to be supported on a square footing at a depth of 7 ft. in silty sand with the following engineering properties: y=119 lb/ft³ above the groundwater table and 122 lb/ft³ below, c'=0, '= 32°, and Neo-30. The groundwater table is 15 ft. below the ground surface. The allowable settlement da is 0.75 inches. The ASD factor of safety is 2.5. Determine the design of the footing width clearly identifying if it is controlled by settlement or bearing capacity.
A continuous footing installed at a depth of 3 feet with base of 4 feet wide is constructed on cohesionless soil with a unit weight of 125 lb/ft³ and an angle of internal friction of 31°. The factor of safety requirement for the design is 2. The water table is sufficiently below the base of the foundation that won't interfere with the design. Determine: 1. Allowable bearing capacity (qa) 2. Allowable wall load in lb/ft. Plb B
raft foundation can be replaced by: Select one: a. pile foundation b. single footing without soil treatment c. none of the above d. single footing with soil treatment
A 10 foot diameter circular footing is to be constructed and will have a net bearing pressure of 2,000 psf. Determine the increase in vertical stress at a depth of 20 feet below the center of the footing the edge of the footing
1. Assuming general shear failure and using the Terzaghi equation with a FOS of 4 find the allowable gross bearing load the following footing can sustain: 3ft continuous footing set 3ft below grade in a 28deg phi soil with a c’ of 400psf and a unit wt of 110psf.
A 3 m square footing supports a vertical column load of 200 kN and two moment loads with axes parallel to the sides of the footing, each having a magnitude of 124 kN-m. The embed-ment of the footing is 1 m, and the groundwater table is at a great depth. Determine whether eccentric loading requirements will be met. If these requirements are not met, determine theminimum footing width, B, needed to satisfy these requirements.
You are planning to build a three story above ground building with a basement parking garage below ground. The bottom of your slab/foundation will be 17 ft below existing grade. You plan to keep the ground water level in the excavation 3.0 ft below the bottom of the foundation for approximately 3 months. The water table is 11 ft below existing grade. The soil is uniform medium sand down to a depth of approximately 50 ft. The soil below 50 ft is an impervious clay. Your excavation will be 320 ft x 150 ft. You have determined that a 4 ft wide x 3 ft deep sump around the perimeter of your excavation will provide adequate dewatering capacity. Based on test wells on site, you determined that the medium sand has a k value of .058 ft/min and that the D factor is 50 ft. a. Label D, H, and ht on the given diagramb. Calculate the flow rate, q c. Calculate the total volume of water that will need to be pumped in gallons per minute (GPM)
Develop a spread sheet to compute allowable total vertical column loads using the ASD methodand factored ultimate vertical column loads using LRFD. The spreadsheet should consider onlyvertical loads on a square or continuous footing bearing on single uniform soil. It should allowthe input of footing width, depth, water table depth, soil strength parameters, a factor of safetyfor ASD, and a geotechnical resistance factor for LRFD. It should compute the bearing capacitybased on both Terzaghi’s and Vesic ́’s methods.
1) Design a rectangular footing for an 16” square corner Column with PDL = 280 kips and PLL = 180 Kips. Make the length of the long side about 1.5 the width of the short side. Fy = 60 ksi F’o= 4000 psi for both, column and footing. Assume the base of the footing is 4'-6" below grade and the depth of the footing is 26". The soil weight is 100 PCF. (Normal weight concrete, No epoxy coating, The Column is reinforced with eight #8 bars.) Need to design for load transfer from the Column to the foating. Need to Show the development length for the dowels. Need to design the bars for footing at both directions. Need to check if the bars fit the footing based on the development legth. Need to show two-way footing Spacing diagram.
3. A vertical load of 155 kips is applied at the center of a footing 5 x 10 ft in plan. How much moment can the footing resist while before the soil pressure exceeds 5 kip/ft and a portion of the footing lifts off the ground?
The underlying soil is a well-graded sand with c′ = 0, f′ = 36°, g = 126 lb/ft3, with a verydeep groundwater table. Using LRFD, design a rectangular footing to meet the ultimate limitstates using a resistance factor of 0.45. Assuming the average CPT tip resistance of the sand is300 kg/cm2, check to see if your design meets serviceability limits. Adjust the design as needed.
A footing is carrying a design column load of 22 k and a moment of 5 k-ft in one direction.The footing will be founded on sand at a depth of 2 ft. The water table is 3 ft below the groundsurface. Design the footing width for a square footing that will carry the design loads and meetthe presumptive allowable bearing pressure per the International Building Code.