What is wrong with this circuit? *

Q: Problem 1: Determine the following: (d) Current gain (e) Power gain (f) Output resistance R₂ Wo 10…

A:

Q: What color fluorescent lamps recommended for residential installation

A: White color fluorescent lamps recommended for residential installation .

Q: Convert both numbers into binary form then construct to circuit in order to calculate the result "S"…

A: Given: Two numbers in decimal as 1453 and 1071 and the digital circuit diagram is asked to perform…

Q: What do call to the encircle part of socket and what is the purpose?

A: It is a 3 pin plug. There are three wires in a 3 pin plug named as- 1 – Earth -E 2 – Neutral -N 3 –…

Q: 11-A certain solar cell type has an output capability of 4.8 A at 0.5 V. A series/ parallel solar…

A: Given that, Current,I = 4.8A Voltage, V = 0.5V No.of cells, N= 104

Q: a p ɔ q e .• 0E f ghij • 30 67 .• 67 • 87 • 27 26. 25 25 • EZ 23 > 2Z 22 21 > 0Z > 6L 18 16 15 > EL…

A: The rows are breadboards are connected horizontally from inside while the columns are connected…

Q: L1 Circuit A 10A Rated Limit Switch Switch Load Contact (25A Rated) C1 20A Load www L2 Circuit B 10A…

A: Switch rating It is defined as the maximum allowable voltage or current that can be passed through…

Q: Q.1 For the power amplifier of Fig. bellow, calculate: (a) Po(ac). (b) P(dc). (c)n %.

A: As per our policy we can provide solution of first three questions only Vcc=40 VRL=8 ΩVin=18…

Q: question 17 AB Calculate the amount of voltage dropped across resistor R₂: 11 1k5 I₁ = 24v 2100 24 V…

A:

Q: Procedure 1. Using the DC circuit trainer, Connect the circuit shown below: R3 820 1000 R2 R4 5 V d…

A: Let, Current i1 flows in the first loop. Current i2 flows in the second loop.

Q: Which pair of circuits are equivalent? 5Ω ww ww 20 V 4 A (4 (a) (b) 4 A 20 V 50 (d) -ww-

A: Which pair of circuits are equivalent given below. We can determine by using source transformation…

Q: List the types of the thyristor protection circuits ? And which one of them is the preferred one

A: For the protection of the Thyristor different methods are used depending on the kind of protection…

Q: An isolator is used to: Select one: a. To be mounted on towers for insulation purpose b. All of the…

A: Isolator is a circuit which separates faulty section from healthy inorder to avoid damage to the…

Q: Three types of electric devices A, B, and C are connected in series across a 115-volt a-c source,…

A: GivenEA=EB=EC=E∠EB=∠EA+90°∠EC=∠EA-90°

Q: 14. With an increase of number of turns of the stator winding of the induction motor * air gap…

A: Induction motor:- It is a type of AC motor. In induction motor squirrel cage or the wound type rotor…

Q: D 00000 R 1Q Q

A: As we can see the clock is provided to the first flip flop only and clock of otger flip flops are…

Q: VDD=2V R= 4KQ R, = 4KQ Rp2 Rp1 M2 HT Pout Cp2 RD1 =4K2 M1 V Rp2 = 4KQ RS1 =4KQ Rs2 6KQ CG Rs2 R2 Rsi…

A:

Q: B1 Battery B2 Battery + A НОНІ Switch B WHOI C 3.30 C 3 VOLTS BAX m 10: KIT NO.

A:

Q: parallel configurations. R₁ and R₂ are as follows: stion 32 Complete the table of values for this…

A:

Q: R

A:

Q: In a balanced Y-A system the phase voltage is 11kV volts [maximum value], the impedance of each load…

A: In the balance star delta system. Phase voltage Vph = 11kV maximum. Load impedance ZL = 12000+j2400…

Q: 7- What is the uses of circuit breaker?

A: Step-1-> A circuit breaker is an electrical safety device designed to protect an electrical…

Q: What does the circuit work like?

A: The above question is based on the firing circuit of a TRAIC.

Q: Suppose the current in this circuit is I = -35 A. The voltage drop across each circuit element is as…

A: Introduction Voltage drop is a term used in electrical engineering to describe the reduction in…

Q: what is the block diagram for this circuit.

A: Given circuit is a light fence circuit that is is used to detect presence of any human or object in…

Q: ONLY circuit B. Circuit A has been completed.

A: Answer is 10* 10^-6 Siemensplease see the solution. Total number of pages are threeExplanation:Step…

Q: 1- Connect the circuit in Figure 3.3 on your bread board. Make sure you record the measured values…

A: Building temporary circuits on a breadboard is common practice. Designers may quickly remove and…

Q: Convert the wiring diagram to circuit diagram

A:

Q: Problem 1: Calculate the values of Vo1 and Vo2 in volts. 12V 500 N 1 kΩ 5V Vo2 5 ΚΩ 500 2 1 kN

A:

Q: Given a system with Transfer Function G(s) = (+1)(+5) F The system settling time in seconds is…

A:

Q: R - 3Ω H = 2 12 V = - 30 V - R = R2 D 4Ω

A:

Q: What code set standard for electrical installation work

A: The NEC provide code set standard for electrical installation work. NEC- National Electrical Code

Q: Consider a LTI system with impulse response h given by h(t) = 200sinc(200nt). Using frequency-domain…

A:

Q: 5- Feedforward control affects the stability of the Feedback control system when they are used…

A: 5. Feedforward control affects the stability of the feedback control system when they are used…

Q: or out of each of the four "nodes" in the circuit. (confirm junction ® Determine the net voltage…

A: The data given in the question is presented in the circuit diagram below,