WHAT IS THE TOTAL SIZE CHANGE OF THE AC BAR

Q: How much current is considered a lethal amount

A: While any amount of current over 10 milliamps (0.01 amp) is capable of producing painful to severe…

Q: List five thing that are typically removed when removing a transaxle

A: The things that are typically removed when removing a transaxle :-

Q: True or False? In a parallel circuit, circuit current is the same throughout all parts of the…

A: Given Data : Parallel circuit

Q: Explain each box. which one is blocked and where is aif flowing

A: Given :-  Two way valve  Three way valve  Four way valve  Four way 5 ported valve

Q: it counted wrong the second part the second q

A:

Q: the operating speed of the relay not depend on Rate of flux built up Armature core air gap Voltage…

A: The operating speed of the relay depends on:- Rate of flux built up  Armature core air gap  Spring…

Q: If the spark line is totally flat, is longer than 2 ms, and is less than 500 volts, there is a good…

A: A sparkline is a line on a chart, that represents the time for which the spark lasts. The height…

Q: Define the pitch of Micrometre Gauge?

A: Micrometre gauge is an instrument which is used for measurement.

Q: A ceiling fan has a light kit attached to the fan. What type of load is the light kit?

A: A ceiling fan has a light kit attached to the fan. What type of load is the light kit? Inductive.

Q: V4 M TAD HD V1 M CYL. 2 FRL M AIH CYL. 1 M V3 LID V2

A:

Q: The load on the outdoor coil influenced by? -The location of the indoor coil -The outdoor…

A: The load on the outdoor coil influenced by the outdoor temperature and the evaporator heat load.

Q: What does a slope in the spark line represent?

A: Sparklines are very small line graphs that are usually drawn without axes or coordinates. In a…

Q: A fixed rating pressure switch is adjusted inside the pressure control and display console to record…

A: Fixed rating pressure switch cannot be adjusted inside the pressure control because due to fixed…

Q: Industrial Main   What is the first step to installing a bearing on a shaft

A:

Q: Why do most automotive spark plugs have a resistor between the top terminal and the centre…

A: When the spark is produced during the ignition stroke of the automotive engine, a burst of the high…

Q: What are the two ways pushrods can be checked for straightness?

A: The pushrods are the connecting link between the rocker arm and the valve lifter. Bent pushrods can…

Q: what are the two tune up methods used for a variety of big bore cummins engines

A: There are two tune up methods used for a variety of big bore Cummins engines. OBC (Outer base…

Q: L. NI Hotor 3. True or false? A magnetic field opposing the stator's magnetic field is produced in a…

A: Lenz's law says that the direction of the electric current induced in a conductor by a changing…

Q: What is normal operating conditions?

A: Normal operating condition refers to the condition at which any machine can work without any fatigue…

Q: When are the loads considered negative?

A: While analyzing a truss or beam or any other structure, we start by assuming all the members…

Q: what happen to the exciter coil as the flywheel rotates past it?

A: Exciter Coil- The very main purpose of this is used to give a stationary rotating magnetic field. It…

Q: what us capable controlling radial load

A: Ball Bearings: Ball bearings are capable of withstanding both radial and axial loads. They…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.