what us capable controlling radial load

Q: Define Straddle hubs.

A: A straddle is a trading strategy that involves options.

Q: How can we locate the position of the neutral axis?

A: Suppose a beam undergoes sagging bending, in this type of bending the upper surfaces undergoes…

Q: What functional problem results from torsion?

A: Given:What functional problem results from torsion?

Q: how to design shaft based on critical speed for agitator?

A: Design of shaft for agitator:- .Tip speed- it is defined by speed of the agitator's blade tip or…

Q: (f) The car drives down a hill of gradient 1 in 5 at a constant 110km/h. What power is required?…

A: Solution to sub-part (f) as mentioned by the student:   given: Effective mass of car = 1850 kg…

Q: 1.5m 15m 0.625 m 3.75 m 0.5 m 60N 0.625 m The frame shown supports a 60 N load at point F. Determine…

A: To find support reaction at pin A,D,C

Q: Determine the load in each member of the truss in figure below 8. 4 В D 16 C E H. A 12 12 12 12 IRH…

A:

Q: Electro-pneumatics Sequential Circuit Problem: Initial position all cylinder are retracted. Pressing…

A: Given : Cycle Operation: Cylinder A extend and hold the work piece. Cylinder B extend for 5 secs.…

Q: Please answer print reading for industry 15-1 # 9, 12, and #15

A: 1) Yes, It is the detailed drawing of one part. This drawing do not have bill of material table. 2)…

Q: What is statically balance forces

A:

Q: What is load and extension

A: Load is basically a force which is exerted on a body or a surface due to which there may be some…

Q: = (1) A circular rod made of steel with a diameter of d = 10 mm and length 1 = 150 mm is shown in…

A: According to the given data d=10mm L=150mm E=300GPa ∆D=-0.015 We need to find The final length of…

Q: The quarter ring shown has a mass m and was cut from a thin, uniform plate. Knowing that r = r2,…

A:

Q: 2. 900N 480 N 4 m A 4m 13 2m C 4 m 4 m - 900ル ー1380N

A: Objective: To draw the moment and load diagram of the given shear force diagram.

Q: Make the definition of Spring Pin and what are the advantages and disadvantages

A: Spring Pin: It is an mechanical fastener. Spring pin is used to tight the relative positon of  two…

Q: What is the distributed loadHow does it act?

A: Load: The load can be defined as the quantity or weight that is carried by a member or a specific…

Q: Q1.With a neat diagram ,explain about the working of Flash Type  ADC

A: Flash Type ADC is based on the principle of comparing analog input voltage with a set of…

Q: Problem 2: A 4 by 4 – in. w0od – post BC is connected to a 1 – in. diameter steel eye – bar AB to…

A: FAy=513FA ∑Mc=0 7000*5=FA*513*7 FA=13000 lbs      (T) σAB=FAA=13000*4π*12=16552.1 psi ∑Fy=0…

Q: What is the Axial Load?

A: The axial load is a force that acts along the centroidal or longitudinal axis of the system. If the…

Q: 4. What are the advantages and disadvantages of using the Wet Mount technique?

A: advantage: Wet-mount: A microscope slide specimen is suspended in a drop of liquid located between…

Q: What remains the same on the input and the output side of a hydraulic jack? What is the drawback to…

A: Hydraulic jack - A hydraulic jack is a mechanical device that is used to lift heavy loads with the…

Q: How would this fourbar linkage actually look?

A: To determine the four bar linkage from the above drawing

Q: 3. Find the Centroid of the Figure shown with respect to x and y-axis. + 12"-

A:

Q: The motor shown in Fig. 1 supplies power P (= 600S kW) at 180 rpm through solid steel motor shaft GF…

A: Here given thattorque developed on      { From diagram}gear F= TF =KN-mTA=KN-mTB=KN-mTD=70 KN-mTe=40…

Q: What are the 3 responses to calculate for under axial load?

A: There are mainly three responses to calculate under axial load: 1) Reactions 2) Buckling, and  3)…

Q: all of a drying oven is construc ctivity k = 0.0705 W/m-K betw ature, T₁= 450°C, and the com

A:

Q: Define the term Distributed loads?

A: In structural mechanics, a load that is distributed continuously over a given area or along a…

Q: What size of hole must be drilled in an M 42 bolt to make the bolt of uniform strength

A:

Q: 5. the absolute maximum bending moment in the simply supported beam due to the wheel loads of the…

A: the resultant force=(4+16+16)k=36kLet the resultant force be at distance x from 16k force (point 3)

Q: Write the Load–Displacement Equations?

A: Given Data⇒Load–Displacement EquationsProblem definition⇒Problem says Write the Load–Displacement…

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.